First Teach-In Step - (Pure) Teaching-In (No Parameters); Second Teach-In Step - Setting Parameters - HomeMatic HM-Sec-Win Montageanleitung Und Bedienungsanleitung

• Tilting/rotating travel speed during locking/unlocking
If a "close" button that has already been taught-in is pressed after configuration mode
has been called up, only the following parameter can be set for the associated profile:
• Travel speed
When assigning parameters, the master remote control does not have to be used for
authentication purposes. Instead, the parameters for buttons on the master remote
control are set once those buttons are pressed.
Pairs of buttons on a remote control always behave in the same way: If the window is
in motion, pressing the other button of the pair will cause it to stop. The "close" button
always behaves in the same way, first stopping the opening movement and then closing
the window.
7.2.2 First teach-in step – (Pure) teaching-in (no parameters)
If a master remote control has not yet been taught-in, you will enter teach-in
mode directly and the remote control to be taught-in becomes the master
remote control. However, if a master remote control has already been taught-in,
the display first shows an "X". You then have three minutes to press a taught-in button
on the master remote control in order to enter teach-in mode; if you do not do this in
time, the process will be cancelled.
To teach-in new control elements, put WinMatic in teach-in mode (long button press
on "close") and, if required, authenticate this step by pressing a button on the master
remote control. If the antenna symbol on the WinMatic display flashes, this indicates
that teach-in mode is active.
If no actions are executed in teach-in mode for three minutes, the mode will be exited.
Now press the teach-in button to initiate the teach-in procedure on the control element
to be taught-in.
After that, press one button of the pair of buttons/the individual button (depending on the
control element in question) to be taught-in. The pair of buttons/individual button is then
taught-in as a close/tilt button with default values.
Teach-in mode is exited automatically following successful teaching-in.
"OK" appears briefly on the display by way of confirmation.
Note: In HomeMatic, control elements are defined as "OFF" or "ON" buttons as
standard and, if required, grouped as an "OFF/ON" pair of buttons. During
teaching-in, the "OFF" button is assigned the "close" function and the "ON"
button the "tilt" function.
54
7.2.3 Second teach-in step – Setting parameters
Press and hold the "open" button (for longer than four seconds) to call up configuration
mode (the mode is exited in the same way). If the antenna symbol flashes, this indicates
that configuration mode is active.
Initially, the display shows "PE".
If the transmitter button to be configured, which has already been taught-in, is then
pressed, „PE" disappears and the parameters can be set.
Configuration mode is exited automatically following successful configuration or if no
entries are made for around three minutes ("antenna" symbol disappears).
Every configuration value entered must be accepted by pressing and holding the
"tilt" button. When you have done this, WinMatic jumps to the next value that can be
configured.
Settings for an "open" button:
The dwell time in the "tilted" state can be set by modifying the value (--, 1 – 99 minutes);
"close" button changes the tens digit and "open" button the units digit. The clock symbol
is also displayed. The "--" value here means that there is no time restriction (i.e. infinitely
long).
Confirm the entry by pressing the "tilt" button (for longer than four seconds).
Next, enter the tilt angle (as a percentage of the maximum possible tilt angle); 0 – 100%.
The percentage symbol is shown on the display, next to the antenna symbol.
Confirm the entry by pressing the "tilt" button (for longer than four seconds).
Finally, enter the travel speed as one of 9 levels: The display shows a "v"
in the first space, followed by a digit (1 – 9).
Once you have confirmed this entry by pressing the "tilt" button (for longer than four
seconds), configuration mode is exited.
55