Cleaning And Maintenance; Storage, Transportation; Troubleshooting; Disposal - Lux Tools A-RT-20 Originalbetriebsanleitung

All manuals and user guides at all-guides.com
Rasentrimmer_Akku_196064.book Seite 24 Montag, 18. November 2019 9:19 09
GB
The remaining capacity of the battery is displayed by
the control lights (14).
Check before starting the device!
DANGER! Risk of injury! The device may
only be put into operation if there are no
defects. If a part is defective it must be
replaced before the device is used again.
WARNING! Risk of injury! Before starting
work check the area and remove all objects
which may be kicked up by the unit.
Check to make sure the device is in safe operating
condition:
– Check to make sure there are no visible defects.
– Check to make sure all device components are
correctly mounted.
Proper position
Hold the unit
• with the left hand on the front handle,
• and the right hand at approximately hip level on
the operating handle,
• balanced in a comfortable way.
Setting the length of the unit
► P. 4, item 7
– Slacken the coupling nut (12).
– Pull the telescopic pole (20) to the desired length.
– Retighten the coupling nut (12) again.
Setting the angle of the cutting head
► P. 4, item 3
– Press in and hold the locking button (11).
– Tilt the cutting head (10) to the required position.
– Release the locking button (11) again.
Switching on and off
– Switching on: Press the switch lock (2) and
simultaneously press the On/Off switch (1).
– Switching off: Release the on-off switch (1).
Error/Fault
Device does not work.
If you can't fix the fault yourself, contact your nearest
vendor. Please be aware that any improper repairs
will also invalidate the warranty and additional costs
may be incurred.

Disposal

Disposal of the appliance
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
with household waste. They may contain
substances that are harmful to the environment and
human health.
24

Cleaning and maintenance

Cleaning and maintenance overview
If necessary
What?
Cleaning the device
Replacing the cutting insert
► P. 5, item 8
– Slide the cutting insert (9) inward and push it out
of the pin (21) on the cutting disk (7).
– Place the new cutting insert (9) on the pin (21)
and pull out the insert until it snaps in.

Storage, transportation

Storage
– Store the tool in a dry and well ventilated place.
Transportation
– When dispatching, try to use the original packag-
ing, if possible.

Troubleshooting

Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possibly
money too.
Cause
Battery not slotted in correctly?
Battery pack discharged?
Battery pack defective?
Is the device defective?
Consumers must dispose of waste electrical devices,
spent portable batteries and rechargeable batteries
separately from household waste at an official collec-
tion point to ensure that these items are processed
correctly. Information on returning these items is
available from the seller. Sellers are required to
accept these items free of charge.
Batteries and rechargeable batteries, which are not
permanently installed in waste electrical devices,
must be removed prior to disposal and must be dis-
posed of separately. Lithium batteries and battery
packs in all systems must only be retuned to a collec-
DANGER! Risk of injury! Remove the bat-
tery pack before conducting any work on the
device.
Note: Clean unit immediately after every
use. Dried grass remains are very hard, and
are very difficult to remove.
How?
Wipe the unit with a damp
cloth.
DANGER! Risk of injury! Unprofessional
repairs may mean that your unit will no
longer operate safely. This endangers you
and your environment.
Remedy
Slot battery into place.
► Charging the battery pack –
p. 23.
Contact your local vendor.