Block Diagram; Rear Panel Connections; Connecting The Ac Adapter; Other Connections - Korg opsix SE Blitzstart

Note
Keyboard
Note
Sequencer
Arpeggiator
Motion
Sequencer
AC adapter

Connecting the AC adapter

1.
Connect the DC plug of the included AC adapter to the DC 12V jack
on the rear panel of the opsix SE.
Be sure to use only the included AC adapter. Using any other AC
adapter may cause malfunctions.
2.
After connecting the DC plug, loop the AC adapter cord onto the Cord
Hook.
Do not use excessive force when pulling the cord off the hook.
Doing so may damage the plug.
3.
Connect the plug of the AC adapter to an AC outlet.
Be sure to use an AC outlet of the correct voltage for your AC
adapter.

Other connections

Connect the opsix SE as appropriate for your audio system.
Be sure that the power on all of your devices is turned off before you
make connections. Leaving the power on when you make connections
may cause malfunctions, or damage your speaker system and other
components.
For the following terminals, use a cable of 3 m or less to prevent
malfunction.
(Headphones) jack, DAMPER jack, USB-B port
OUTPUT L/MONO, R jacks: Connect these TRS jacks to a mixer, audio
interface, monitor system, etc. Adjust the volume level using the VOLUME knob.
(Headphones) jack: Connect the headphones here. This carries the same
signal as that of OUTPUT L/MONO and R.
DAMPER jack: Connect a Korg DS-1H damper pedal or a PS-1/PS-3 pedal
switch (sold separately) to control the damper function. Pedal polarity is
detected automatically; to allow this, make sure that the pedal is not held
down when connected, or while turning on power.

Block Diagram

Algorithm
Operator
Operator
Operator
Operator Operator
Operator
Operator 1...6
Pitch Level EG
Key Track
EG1 LFO 1 LFO 2

Rear panel connections

DC 12V jack MIDI IN, OUT connectors
Cord hook (Power) buttton
MIDI cable MIDI cable
(included)
MIDI IN
Sound module,
DAW MIDI interface, etc.
FX1
Filter
EG2 EG3
LFO 3
Virtual Patch
OUTPUT L/MONO,
DAMPER jack
R jacks
(USB B) port
Damper pedal,
Pedal switch, etc.
USB cable
MIDI OUT
USB
MIDI keyboard, Computer
DAW MIDI interface, etc.
MIDI IN, OUT connectors: Use these connectors to connect the opsix SE to
an external MIDI device for exchanging MIDI messages. Make sure that the
MIDI channels are set appropriately.
USB B port: Connect this to a computer to exchange MIDI messages and
data.

Turning the power on/off

Turning the opsix SE On

Make sure that both the opsix SE and any amplification devices such as
powered monitor speakers are turned off, and turn the volume of all devices
all the way down.
1.
Hold down the rear-panel
appears in the display, release the
2.
Turn on any amplification devices such as powered monitor speakers,
and then adjust their volume. Adjust the opsix SE's volume using the
VOLUME knob.

Turning the opsix SE Off

1.
Lower the volume of your powered monitors or other amplification
devices, and turn them off.
2.
Hold down the opsix SE
"Shutting down," and then release the

Auto Power-Off

By default, the opsix SE will automatically turn off after about four hours
have elapsed without use of the front panel, keyboard, or MIDI input. See
the Owner's Manual (PDF) for details on how to disable this function.
En-5
Master
OUTPUT
FX2 FX3
Volume
(Headphones) jack
Headphones
Input L
Input R
Mixer, Monitors,
Audio Interface, etc.
(power) button. Once the "opsix" logo
(power) button.
(power) button until the display shows
(power) button.