Handling The Co 2 Bottle - Kärcher WPD 200 Advanced Bedienungsanleitung

Initial Start-Up menu
1. Plug the mains plug into the socket.
2. Set the power switch to "1".
Display
>Begin initiation? YES<
Plus / Increase button
1
Minus / Reduce button
2
Enter button
3
Back / Stop button
4
Blue / red LED
5
Text messages
6
The "Plus" and "Minus" buttons can be used to se-
lect submenus and to increase or decrease adjusta-
ble values (flashing display).
The "Enter" button can be used to confirm indica-
tions in the display or entries.
The "Back" button can be used to return to the pre-
vious step or to exit the menu level.
Display
>Language<
Selectable languages
Selected language
>Current date / time<
Set day (display flashes)
Set month (display flashes)
Set year (display flashes)
Set hours (display flashes)
Set minutes (display flashes)
Set Date / Time
>Filter used?<
>Water supply Connected?<
>Can under the dispenser?
>Initial start-up running mm:ss min<
Note
During initial Start-Up, the lines of the individual water
types are rinsed. This procedure takes about 17 min-
utes.
The water dispensed during the rinsing process is not
suitable for consumption!
During the rinsing process, the container under the wa-
ter outlet must be emptied several times.
Display
>Initial start-up running mm:ss min<
>Initial Start-Up interrupted, Continue!<
3. Empty the container and place it under the water
outlet again.
Display
>Initial Start-Up interrupted, Continue!< Enter
After completion of the initial Start-Up, thermal sani-
tisation must be carried out.
Display
>Carry out disinfection! Device hygiene
otherwise not guaranteed.<
>Yes<
>Later<
The thermal sanitisation takes approx. 70 minutes.
During this time, the device cannot be operated. The
somewhat louder operating noise during the clean-
ing process is normal. After cleaning, the hot water
is flushed directly into the waste water pipe or into
the optional can. See also Chapter ' Sanitisation da-
ta'. After completion of the thermal sanitisation, the
device is ready for operation.
20
Handling the CO
Note
Please also note the general information on handling
Button
CO bottles, see chapter General instructions for han-
2
dling CO bottles.
Enter 2
When connecting a new, or removing an old CO
follow the steps below.
Opening the door of the stand
The door of the stand is lockable.
1. Unlock the door lock.
Illustration I
Door lock
1
Stand
2
Cup dispenser (conversion kit)
3
Door of stand
4
2. Open the door of the stand.
Removing the empty CO
If the button for carbonated water (Sparkling) is inactive
and "CO empty" flashes, either no CO2 bottle is con-
2
nected or the CO
2
Button
1. Set the power switch to "0".
Enter
2. Open the door of the stand.
Plus / Minus
3. Turn the control knob to "0".
Enter
Illustration J
Enter
Control knob
1
Enter
Pressure reducer
2
Enter
Union nut
3
Enter
Main tap
4
Enter
Pressure gauge control pressure
5
Enter
CO hose
6
2
Enter
Note
If the pressure reducer is separated from the CO
Enter
when sufficient pressure is still present, the O-ring be-
Enter
tween the bottle and the pressure reducer will be de-
formed and must be replaced.
4. Unscrew the pressure reducer from the empty gas
bottle.
5. Screw the protective cover onto the empty gas bot-
tle.
6. Release the tensioning strap for securing the empty
gas bottle.
7. Remove the empty gas bottle.
Connecting a new CO
1. Insert the new gas bottle into the stand.
Button
2. Secure the gas bottle with the tensioning strap.
Back (X)
3. Unscrew the protective cover of the new gas bottle.
4. Briefly open the main tap of the gas bottle so that
any liquid CO
2
Illustration J
Control knob
1
Button
Pressure reducer
2
Union nut
3
Main tap
4
Button
Pressure gauge control pressure
5
Enter
CO hose
6
2
5. Screw the pressure reducer onto the new gas bottle.
Enter
Note: Ensure that the sealing ring is fitted correctly.
Back
6. Slowly open the main tap.
7. Set to 3 bar with the control knob on the pressure re-
ducer.
8. Close the main tap.
9. Read the displayed value on the control pressure
gauge.
bottle
2
bottle,
2
bottle
2
bottle is empty and must be replaced.
bottle
2
bottle
2
that may be present can escape.
English
10. The displayed value must remain constant for at
least 5 minutes. If there is a noticeable drop in pres-
sure:
a Check that the O-ring between the gas bottle and
the pressure reducer is present and undamaged.
b Replace a defective O-ring.
c Check that the pressure reducer is fitted correct-
ly.
d Tighten the union nut firmly.
e Check the hose connector on the CO
on the pressure reducer for visible damage. If in
doubt, call customer service.
f If the pressure drop cannot be stopped by the
measures mentioned, the pressure reducer is de-
fective and must be replaced.
11. Open the main tap.
12. Set the power switch to "1".
13. Remove carbonated water from the device and
check that the pressure remains constant.
14. Adjust the pressure if necessary.
15. Close the door of the stand.
16. Place a container under the water outlet.
17. Dispense 1 litre of water so that the CO
up again.
Adjusting the compensation controller
The compensation controller is used for fine regulation
of the dispensing quantities of carbonated water during
portioned dispensing. The delivery volume of the water
types "Ambient" and "Chilled" is not affected.
Before selecting the "Serving amount Custom" operat-
ing mode, it is necessary to adjust the compensation
controller in the "Serving amount Standard" operating
mode. If the adjustment is incorrect, a larger quantity of
carbonated water cannot be dispensed.
1. Adjust the operating mode "Serving amount Stand-
ard".
2. Place a measuring cup with a volume of more than
1 litre under the water outlet.
3. Select 1 litre of carbonated water "Sparkling".
4. Measure the actual amount of water delivered.
5. Remove the drip tray.
6. Open the device door.
The adjusting wheel of the compensation controller
is located behind the water outlet.
Illustration K
Adjusting wheel of compensation controller
1
Water outlet
2
● If the adjusting wheel is turned clockwise, the serv-
ing amount is reduced.
● The total adjustment range is 4 turns.
● Standard position approx. 2.5 turns.
● With stronger throttling, not only does the serving
amount decrease, but also the CO
creases significantly.
7. Adjust the compensation knob in the required direc-
tion.
8. Select 1 litre of carbonated water again "Sparkling"
and repeat the procedure until the amount of water
dispensed is correct.
Note
Serving amount is also dependent on feed pressure and
CO pressure. The CO pressure must be in the range
2 2
between 3.0 and 3.5 bar during CO
value is set, fine adjustment is made on the compensa-
tion controller.
hose and
2
mixer fills
2
content de-
2
delivery. Once this
2