Specifications; Functional Description - Makita 3709 Betriebsanleitung

ENGLISH
(Original instructions)
1 Base
2 Scale
3 Bit protrusion
4 Clamping nut
5 Adjusting screw
6 Switch lever
7 Loosen
8 Tighten
9 Hold
10 Workpiece
11 Feed direction

SPECIFICATIONS

Model
Collet chuck capacity................................... 6 mm or 1/4"
–1
No load speed (min ) ........................................... 30,000
Overall length ...................................................... 199 mm
Net weight............................................................... 1.5 kg
Safety class ...............................................................
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
TRIMMER SAFETY WARNINGS
1. Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
3. Wear hearing protection during extended period
of operation.
4. Handle the bits very carefully.
5. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Explanation of general view
12 Bit revolving direction
13 View from the top of the tool
14 Straight guide
15 Base protector
16 Screws
17 Screwdriver
18 Bit
19 Templet
20 Templet guide
21 Bolt
22 Guide plate
6.
3709
7.
8.
9.
10. Before using the tool on an actual workpiece, let
/II
11. Be careful of the bit rotating direction and the
12. Do not leave the tool running. Operate the tool
ENE010-1 13. Always switch off and wait for the bit to come to
14. Do not touch the bit immediately after operation;
ENF002-2
15. Do not smear the tool base carelessly with thin-
16. Use bits of the correct shank diameter suitable
17. Some material contains chemicals which may be
GEA010-1
18. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
GEB019-4
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
23 Wing nut
24 Clamp screw (A)
25 Centre hole
26 Nail
27 Clamp screw (B)
28 Trimmer guide
29 Guide roller
30 Limit mark
31 Brush holder cap
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
for the speed of the tool.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
the material and application you are working
with.
5