Black & Decker MTOS4 Bersetzt Von Den Originalanweisungen Seite 7

Š Slide the accessory (11) between the shaft and the
accessory holder making sure the acces- sory engages all
eight pins on the holder and is flush with the shaft.
Š Release the accessory clamping lever.
NOTE: Some accessories, such as scrapers and blades can
be mounted at an angle if required.
Fitting a sanding sheet (fig. B)
Š Line up the sanding sheet (12) with the sand- ing base
(13) as shown.
Š Press the sheet firmly and evenly onto the sanding base,
making sure that the holes in the sheet coincide with the
holes in the base.
Removing a sanding sheet
@
Š Pull the sanding sheet (12) off the sanding base (13).
Warning! Never use the sanding base without a
sanding sheet or accessory in place.
Fitting the dust extraction adaptor (fig. B)
Š Line up the vacuum adaptor (15) with one end of the tube
(14) as shown.
Š Press the adaptor firmly and evenly in to the tube.
Š Line up the tube (14) with the sanding base (13) as
shown.
Š Press the tube firmly and evenly on to the sanding base.
Š Secure the tube by turning the locking nut (16) clockwise.
Š Connect a vacuum cleaner to the vacuum adaptor.
Removing the dust extraction adaptor
Š Turn the locking nut (16) anti-clockwise.
Š Pull the tube(14) out of the sanding base (13).
Fitting alternative accessories (fig. C)
Š Place the spacer (17) onto the collar (18).
Š Place the alternative accessory (19) onto the collar (18).
Š Firmly attach the fixing bolt (20) into place to ensure a
tight fit for the alternative accessory (19) with the hex key
provided.
NOTE: The spacer and fixing bolt are not used to attach
BLACK+DECKER accessories. Black and Decker accessories
are attached using the Super- lokTM Tool free accessory
clamping lever.
@
Use
Warning! Let the tool work at its own pace. Do not
overload.
(Original instructions)
Variable speed control (fig. A)
NOTE: Ensure the forward reverse slider (2) is not in the
locked position.
Š To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
Š To switch the tool off, release the variable speed switch.
Hints for optimum use
Š Always hold the tool securely. For precision work, hold the
tool near the front.
Š Clamp the workpiece whenever possible, especially when
using cutting blades.
Š Do not exert too much pressure on the tool.
Š Always use the appropriate type of attachment for the
workpiece material and type of cut.
Š Regularly check the condition of accessories.Replace
when necessary.
Š Mark the desired starting point.
Š Switch the tool on and slowly feed attachments into the
workpiece at the desired starting point.
Š Clamp a piece of plywood or soft wood to the back of the
workpiece and saw through the combination in order to
obtain a clear cut.
Š Do not force the cutting blade into the workpiece. Note
that cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
Š When cutting metal spread a thin film of oil along the
cutting line before cutting.
Š When sanding new layers of paint before ap- plying
another layer, use extra fine grit.
Š On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Š Consult your retailer for more information on available
accessories.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
Š Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Š Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
ENGLISH
7