Symbols On The Device; Description Of The Device; Installation; Initial Startup - Kärcher FC 7 Cordless Bedienungsanleitung

cleaning rollers ● Risk of injury from sharp objects (e.g.
splinters). Protect your hands while cleaning the floor
head.
CAUTION
● Do not use the appliance if it has
been dropped beforehand, is visibly damaged or if it is
leaking. ● Only operate or store the device in accord-
ance with the description or figure. ● Accidents or dam-
age due to the device falling over. Before all actions with
or on the device, you must make sure that it is stable.
● Never leave the device unsupervised while it is in op-
eration.
ATTENTION
● Device damage. Never fill the wa-
ter reservoir with solvents, liquids containing solvents or
undiluted acids (e.g. detergents, petrol, paint thinners
and acetone). ● Only switch on the device when the
fresh water tank and waste water tank are installed.
● Do not pick up sharp or larger objects with the device,
such as e.g. glass shards, gravel or toy parts. ● Do not
fill the fresh water container with vinegar, decalcification
agents, essential oils or similar substances. Avoid tak-
ing up these substances with the device. ● Use the de-
vice only on hard floors with a watertight coating, such
as e.g. varnished parquet, enamelled tiles or linoleum.
● Do not use the device for cleaning carpets or carpeted
floors. ● Do not guide the device over the floor grilles of
convection heating systems. The device cannot vacu-
um up the escaping water when it is guided over a floor
grille. ● In case of longer breaks in operation and after
use, switch off the device at the main switch / device
switch and pull out the charged mains plug. ● Do not op-
erate the device at temperatures below 0 °C. ● Protect
the device from rain. Do not store the device outdoors.

Symbols on the device

● The warning for not cleaning the
floor head under running water is lo-
cated:
–
on the bottom of the floor head.
● Symbols for unit cleaning mode after finishing work
are located:
–
engraved in the bowl of the cleaning station,
–
as a label on the back of the fresh water tank.
● Symbols for unlocking the waste water tank/parking
station are located:
–
as a label on the unlocking button for the waste
water tank/parking station.
The application and description of the symbols (see
chapter Floor head cleaning by means of rinsing pro-
cess).

Description of the device

The maximum amount of equipment is described in
these operating instructions. Depending on the model
used, there are differences in the scope of delivery (see
packaging).
For the illustrations, refer to the graphics page.
Illustration A
ON/OFF switch
1
Boost function button
2
Increased roller speed and additional water quantity
for stubborn dirt
16
Button for adjusting the cleaning level
3
Switching between cleaning level 1 and 2
"Cleaning level 2" indicator
4
Increased roller speed and amount of water
"Cleaning level 1" indicator
5
Normal roller speed and amount of water
"MAX" indicator (red)
6
The waste water tank is full
"MIN" indicator (blue)
7
The fresh water tank is empty
"Battery" indicator (green)
8
Indicates the charging state of the battery
Wall anti-slip handle
9
Handle
10
Fresh water tank
11
Removable hair filters
12
Unlocking button for the waste water tank and park-
13
ing station
Cleaning rollers (4 x)
14
Waste water tank
15
* LED lighting
16
Unlocking button for hair filters
17
Charging socket
18
Parking station
19
Cleaning station with cleaning brush
20
Charger with charging cable
21
* Cleaning rollers for stone floors (4 x)
22
Detergent RM 536 (30 ml)
23
* Detergent RM 537 (30 ml)
24
* Detergent RM 536 (500 ml)
25
* optional
Installing the handle bar
1. Hold the basic device firmly.
2. Place the cable in the guide of the plastic connector
and fix it.
3. Fit the handle bar all the way to the end stop into the
basic device until it audibly latches into place. The
handle bar must sit tightly in the device.
Illustration B
Charging process
1. Plug the charging cable of the charger into the
charging socket on the device.
Illustration C
2. Plug the mains plug of the charger into the socket.
The LED indicator lights display the battery's current
charging state.
Illustration D
● All 3 LED indicator lights flash from bottom to top
when charging a completely empty battery.
English

Installation

Initial startup