Makita UC100D Betriebsanleitung Seite 14

3. R e m o v e t h e s p r o c k e t c o v e r .
4. A l i g n t h e h o l e o n t h e g u i d e b a r w i t h t h e p i n o n t h e
t o o l b o d y , a n d t h e n p l a c e t h e g u i d e b a r a s s h o w n i n t h e
figure.
Fig.10: 1. G u i d e b a r 2. H o l e 3. P i n
5. S l i d e t h e g u i d e b a r t o w a r d t h e s p r o c k e t t o l o c k t h e
p i n .
Fig.11: 1. G u i d e b a r 2. P i n
6. R e m o v e t h e g u i d e b a r f r o m
7.
C h e c k t h e d i r e c t i o n o f t h e s a w c h a i n . M a t c h t h e
d i r e c t i o n o f t h e s a w c h a i n w i t h t h a t o f t h e m a r k o n t h e
t o o l b o d y .
Fig.12: 1. M a r k o n t o o l b o d y
8. F i t o n e e n d o f t h e s a w c h a i n o n t h e t o p o f t h e
g u i d e b a r .
9. F i t t h e o t h e r e n d o f t h e s a w c h a i n a r o u n d t h e
s p r o c k e t , t h e n a t t a c h t h e g u i d e b a r t o t h e t o o l b o d y s o
t h a t t h e h o l e o n t h e g u i d e b a r i s a l i g n e d w i t h t h e p i n o n
t h e b o d y .
Fig.13: 1. S p r o c k e t
P r e s s t h e g u i d e b a r a g a i n s t t h e t o o l b o d y t o r e l e a s e t h e
pin. The saw chain tension is automatically adjusted.
Fig.14: 1. S a w c h a i n 2. P i n 3. S p r o c k e t
10. P l a c e t h e s p r o c k e t c o v e r s o t h a t t h e b o l t a n d p i n
o n t h e t o o l b o d y m e e t t h e i r c o u n t e r p a r t s o n t h e s p r o c k e t
c o v e r .
Fig.15: 1. S p r o c k e t c o v e r 2. B o l t 3. P i n
11. T u r n t h e l e v e r c l o c k w i s e u n t i l t h e s p r o c k e t c o v e r i s
s e c u r e d t h e n r e t u r n i t t o t h e o r i g i n a l p o s i t i o n .
Fig.16: 1. L e v e r 2. S p r o c k e t c o v e r
M a k e s u r e t h a t t h e s a w c h a i n d o e s n o t l o o s e a n d t h e
s a w c h a i n c a n b e m o v e d s m o o t h l y b a c k a n d f o r t h . I f
necessary, adjust the tension of the saw chain by refer-
ring to the section for adjusting saw chain tension.
Adjusting saw chain tension
CAUTION:
A chain which is too loose can
jump o the bar and it may cause an injury or
accident.
T h e s a w c h a i n m a y b e c o m e l o o s e a f t e r m a n y h o u r s
o f u s e . F r o m t i m e t o t i m e c h e c k t h e s a w c h a i n t e n s i o n
b e f o r e u s e .
If the saw chain is loose, adjust the saw chain tension.
1.
P u l l t h e l e v e r u p .
Fig.17: 1. L e v e r
2. T u r n t h e l e v e r c o u n t e r c l o c k w i s e a l i t t l e t o l o o s e n
the sprocket cover lightly. The chain tension is adjusted
a u t o m a t i c a l l y .
Fig.18: 1. S p r o c k e t c o v e r 2. L e v e r
3. T u r n t h e l e v e r c l o c k w i s e u n t i l t h e s p r o c k e t c o v e r i s
s e c u r e d t h e n r e t u r n i t t o t h e o r i g i n a l p o s i t i o n .
Fig.19: 1. L e v e r 2. S p r o c k e t c o v e r
t h e t o o l b o d y .
14 ENGLISH
OPERATION
Lubrication
CAUTION:
Do not operate the tool when the
tank is empty. Replenish the oil in due time before
the tank is empty.
CAUTION:
Prevent the oil from coming into
contact with the skin and eyes. Contact with the
eyes causes irritation. In the event of eye contact,
ush the a ected eye immediately with clear
water, then consult a doctor at once.
CAUTION:
Never use waste oil. Waste oil contains
carcinogenic substances. The contaminants in waste
oil cause accelerated wear of the oil pump, the bar and
the chain. Waste oil is harmful to the environment.
NOTICE:
When the tool is used for the first time,
it may take up to two minutes for the saw chain oil
to begin its lubricating e ect upon the saw mech-
anism. Run the saw without load until it does so.
NOTICE:
When filling the chain oil for the first time,
or refilling the tank after it has been completely emp-
tied, add oil up to the bottom edge of the filler neck.
The oil delivery may otherwise be impaired.
NOTICE:
Use the saw chain oil exclusively for
Makita tools or equivalent oil available in the market.
NOTICE:
Never use oil including dust and parti-
cles or volatile oil.
NOTICE:
When pruning trees, use botanical oil.
Mineral oil may harm trees.
NOTICE:
Before the cutting operation, make sure
that the provided oil tank cap is screwed in place.
S a w c h a i n i s a u t o m a t i c a l l y l u b r i c a t e d w h e n t h e t o o l i s i n
o p e r a t i o n . C h e c k t h e a m o u n t o f r e m a i n i n g o i l i n t h e o i l
t a n k p e r i o d i c a l l y t h r o u g h t h e o i l i n s p e c t i o n w i n d o w .
Fig.20: 1. O i l i n s p e c t i o n w i n d o w 2. O i l t a n k c a p
To fill the oil, perform the following steps:
1. C l e a n t h e a r e a a r o u n d t h e o i l t a n k c a p t h o r o u g h l y
t o p r e v e n t a n y d i r t f r o m
2. L a y t h e t o o l o n i t s s i d e .
3.
P u s h t h e b u t t o n o n t h e o i l t a n k c a p s o t h a t t h e
b u t t o n o n t h e o t h e r s i d e s t a n d s u p , a n d t h e n r e m o v e t h e
o i l t a n k c a p b y t u r n i n g i t .
Fig.21: 1. O i l t a n k c a p 2. T i g h t e n 3. L o o s e n
4. F i l l t h e o i l t a n k w i t h t h e o i l . T h e p r o p e r a m o u n t o f o i l i s 55 m l .
5. Screw the oil tank cap firmly back in place.
6. W i p e a w a y a n y s p i l t c h a i n o i l c a r e f u l l y .
NOTE: If it is di cult to remove the oil tank cap, insert
t h e t i p o f s l o t t e d s c r e w d r i v e r i n t o t h e s l o t o f t h e o i l
t a n k c a p , a n d t h e n r e m o v e t h e o i l t a n k c a p b y t u r n i n g
i t c o u n t e r c l o c k w i s e .
Fig.22: 1. S l o t 2. S l o t t e d s c r e w d r i v e r
After refilling, hold the tool away from the material to be cut.
S t a r t i t a n d w a i t u n t i l l u b r i c a t i o n o n s a w c h a i n i s a d e q u a t e .
Fig.23
e n t e r i n g t h e o i l t a n k .