Troubleshooting; Important Safety Instructions - Remington HC363C Anleitung

ENGLISH
STEP 5 – The fi nishing touches – PICTURE 5
Use the clipper without an attachment comb for close trimming around the base and sides
of the neck. Use the ear comb guides to get a clean line around each ear. For the required
ear comb guide, angle the clipper and lightly stroke around each ear to the back of the
neck.
To produce a clean straight line at the sideburns, reverse the hair clipper. Place the
reversed clipper at right angles to the head, tips of the blades lightly touching the skin and
then work downwards.
SHORT TAPERED STYLES – "FLAT TOPS" & SHORT CUTS
Starting with the longest guide comb attached (25mm), cut from the back of the neck to
the crown. Hold the guide comb fl at against the head and slowly move the clipper through
the hair, as shown. (PICTURE 1)
Use the same procedure from the lower side to the upper side of the head, as illustrated.
Then cut the hair against the direction in which it grows and level with the sides.
(PICTURE 3)
To give a "fl at top" look, the hair on top of the head must be cut over the top of a fl at
comb.
Use a closer guide comb to taper the hair down to the neckline as desired.
TAPER LEVER
This product has a taper lever located a the left side of the clipper near the blades. Adjust
the lever to change the closeness of the cut gradually and also to improve the effectiveness of
the comb attachments. The taper lever also extends the life of the blades because a different
cutting edge is used in each setting.
CARE FOR YOUR HAIRCLIPPER
Your clipper is fi tted with high quaity ceramic blades that are premanently lubricated. To
ensure long lasting performance of your clipper, clean the blades and unit regularly. Always
keep the protective cap on the trimmer blade.
AFTER EACH USE
Ensure the clipper is switched off and disconnected from the mains.
Brush the accumulated hair from the blades. Do not submerge the clipper in water.
To clean the unit, wipe with a damp cloth and dry immediately.
Note: Ensure that the clipper is turned off when cleaning.
EVERY SIX MONTHS
At regular intervals the Blade Set should be removed and cleaned.
Remove the 2 screws retaining the fi xed blade with a screwdriver. Do not remove blade
set.
4
061015_REM_HC363_RZ_02.indd 4-5 061015_REM_HC363_RZ_02.indd 4-5
Brush out hairs from between the blades with soft cleaning brush. Do not remove the
lubricating grease from the blades. It is not necessary to remove the small moving blade
from the unit.
If the moving blade has been removed this can be re-fi tted by slotting the ceramic blade
holder over the pin in the centre of the interior product head. The groove on the ceramic
blade, just below the teeth, rests on a metal plate at the opposite side to the screw holes.
The fi xed blade is fi tted with the raised profi le pointing outwards and fi xed with the 2
screws.
Before fully tightening the 2 screws, adjust the taper lever to the lower position and align
the blades so that their cutting edges are parallel to one another. Tighten the 2 screws.
Note that if the blades are not correctly aligned then cutting effi ciency will be impaired.
Place a few drops of cutter or sewing machine oil onto the blades. Wipe off excess oil.
CAUTION: Do not use liquid cleaners on the blades or harsh or corrosive chemicals on
the blade casing. Always use a soft brush to remove the accumulated hairs.
Unplug the charge adaptor from the power outlet when fi tting or removing attachments,
or while cleaning the product.
Always store this appliance and cord in a moisture-free area.
Do not wrap the cord of the charging adaptor around the appliance.

TROUBLESHOOTING

If blades do not seem to cut hair easily, the taper lever (PICTURE 6) can be used to remove
any hair caught between the comb and blade. Switch the clipper on and move the taper lever
up and down a few times but do not force the lever in either direction. This should remove
hairs and restore the cutting effi ciency. If not, contact your nearest Remington Service
Centre.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR
INJURY TO PERSONS:
An appliance should never be left unattended when plugged into a power outlet.
Keep the power plug and cord away from heated surfaces.
Make sure the power plug and cord do not get wet.
Do not plug or unplug the shaver with wet hands.
Do not use the product with a damaged cord. A replacement can be obtained via our
International Service Centres.
Charge, use and store the product at a temperature between 15°C and 35°C.
Always unplug from the mains when cleaning.
Only use the parts supplied with the appliance.
Keep away from children.
5
15.11.2006 15:12:47 Uhr 15.11.2006 15:12:47 Uhr