Package Contents; Description (Fig. A); Changing Blades - DeWalt DWE5615 Bersetzung Der Originalanweisungen

Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Circular saw
1 Circular saw blade
1 Hex key
1 Parallel fence
1 Dust extraction spout
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection
Date Code Position (Fig. A)
The date code 13 , which also includes the year of manufacture,
is printed into the housing.
Example:
2022 XX XX
Year and Week of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Main handle
2
Blade lock
3
Auxiliary handle
4
Bevel adjustment knob
5
Bevel angle adjustment mechanism
6
Base plate
7
Lower blade guard
8
Blade clamping screw
9
Lower guard lever
10
Upper blade guard
11
Lock‑off button
12
Intended Use
This heavy‑duty circular saw is designed for professional wood
cutting applications.
DO nOt use under wet conditions or in the presence of
2 ; the
flammable liquids or gases.
This heavy‑duty saw is a professional power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

Changing Blades

To Install the Blade (Fig. A–C)

WARNING: Disconnect tool from power source before
service, adjustment, installing or removing accessories.
1. Place inner clamp washer
2. Retract the lower blade guard
spindle against the inner clamp washer, making sure that
the blade will rotate in the proper direction (the direction
of the rotation arrow on the saw blade and the teeth must
point in the same direction as the direction of rotation arrow
on the lower blade guard). Do not assume that the printing
on the blade will always be facing you when properly
installed. When retracting the lower blade guard to install
the blade, check the condition and operation of the lower
blade guard to assure that it is working properly. Make sure
it moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
3. Place outer clamp washer
flat surface against the blade with beveled side facing out.
4. Thread blade clamping screw
hand (screw has left‑hand threads and must be turned
counterclockwise to tighten).
5. Depress the blade lock button
spindle with the hex key
and the blade stops rotating.
6. Tighten the blade clamping screw firmly with the
blade wrench.
nOtE: Never engage the blade lock while saw is running, or
engage in an effort to stop the tool. Never turn the saw on
while the blade lock is engaged. Serious damage to your saw
will result.
EngLIsh
on saw spindle properly.
14 15
8 and place blade on saw
on saw spindle with the large
16
9 into saw spindle by
3 while turning the saw
17 until the blade lock engages
29