Light Mode - Makita TD003G Betriebsanleitung

Light mode

You can use the tool as a handy light.
Turning on / o the light mode
T o t u r n o n t h e l i g h t , s e t t h e r e v e r s i n g s w i t c h l e v e r i n t h e
n e u t r a l p o s i t i o n a n d p u l l t h e s w i t c h t r i g g e r .
The lamp keeps lighting up for approximately one hour.
To turn o the light mode, pull the switch trigger again or
d e p r e s s t h e r e v e r s i n g s w i t c h l e v e r .
NOTE: Y o u c a n n o t c h a n g e t h e a p p l i c a t i o n m o d e
w h i l e t h e l i g h t m o d e i s o n . T h e l a m p s o n t h e s w i t c h
p a n e l d o n o t t u r n o n w h e n t h e l i g h t m o d e i s o n .
NOTE: You cannot turn on/o the lamp status or
c h a n g e t h e a p p l i c a t i o n m o d e w h e n t h e l i g h t m o d e i s
o n .
NOTE: T h e l i g h t m o d e d o e s n o t w o r k w h e n t h e t o o l /
battery protection system activates or the battery
capacity is not enough.
Changing the impact force
You can change the impact force in five steps:
T h i s a l l o w s a t i g h t e n i n g s u i t a b l e t o t h e w o r k .
" T " i s a s p e c i a l m o d e f o r f a s t e n i n g s e l f - d r i l l i n g s c r e w s . T h i s m o d e h e l p s t o p r e v e n t t h e s c r e w s f r o m
also accomplishes quick operation and good finish at the same time. The tool drives a screw with high-speed rotation
a n d s t o p s s o o n a f t e r t h e t o o l s t a r t s t o i m p a c t .
The level of impact force changes every time you press the button
You can change the impact force within approximately one minute after releasing the switch trigger.
NOTE: You can extend the time to change the impact force approximately one minute if you press the button
b u t t o n .
Fig.8
Application mode
(Impact force grade
displayed on panel)
4 ( M a x )
3 ( H a r d )
2 ( M e d i u m )
(max),
Maximum blo w s
-1
4 , 100 m i n ( / m i n ) T i g h t e n i n g w i t h t h e m a x i m u m
a n d s p e e d .
-1
3 , 6 00 m i n ( / m i n ) T i g h t e n i n g w i t h l e s s f o r c e a n d s p e e d
t h a n M a x m o d e ( e a s i e r t o c o n t r o l t h a n
M a x m o d e ) .
-1
2, 6 00 m i n ( / m i n ) Tightening when a good finishing is
n e e d e d .
Changing the application mode
W hat' s the application mode?
T h e a p p l i c a t i o n m o d e i s t h e v a r i a t i o n o f t h e d r i v i n g
rotation and impact which are already preset in the tool.
By choosing a suitable application mode depending on
the work, you can accomplish quicker work and/or more
beautiful finish.
T h i s t o o l f e a t u r e s f o l l o w i n g a p p l i c a t i o n m o d e s :
Impact force
• 4 ( M a x )
• 3 ( H a r d )
• 2 ( M e d i u m )
• 1 ( S o f t )
• T m o d e
The application mode can be changed by the but-
t o n o r b u t t o n .
Fig.7: 1. B u t t o n
NOTE: W h e n n o n e o f t h e l a m p o n t h e p a n e l i s l i t , p u l l
t h e s w i t c h t r i g g e r o n c e .
NOTE: Y o u w i l l n o t b e a b l e t o c h a n g e t h e a p p l i c a t i o n
mode if you do not operate the tool for approximately
o n e m i n u t e . I n t h i s c a s e , p u l l t h e s w i t c h t r i g g e r o n c e
a n d p r e s s t h e b u t t o n
(hard), (medium), 1 (soft) and T mode.
o r b u t t o n
Purpose
f o r c e
9 ENGLISH
2. B u t t o n
o r b u t t o n .
o v e r - t i g h t e n i n g . I t
.
Example of application
Dr i v i n g s c r e w s t o u n d e r w o r k m a t e r i -
a l s , t i g h t e n i n g l o n g s c r e w s o r b o l t s .
Dr i v i n g s c r e w s t o u n d e r w o r k m a t e r i -
a l s , t i g h t e n i n g b o l t s .
Driving screws to finishing boards or
p l a s t e r b o a r d s .
o r