Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
3. Turn the chainsaw on then rotate the saw chain and bar
down into the tree, using the spike as a hinge.
4. Once the chainsaw gets to a 45 ° angle, level the chainsaw
again and repeat steps until you cut fully through.
5. When the tree is supported along its entire length, make a
cut from the top (overbuck), but avoid cutting the earth as
this will dull your saw quickly.
23
•
When supported at one end first, cut 1/3 the diameter from
the underside (underbuck). Then make the finishing cut by
overbucking to meet the first cut as shown below.
2
1
•
When supported at both ends. First, cut 1/3 down from the top
overbuck. Then make the finished cut by underbucking the
lower 2/3 to meet the first cut as shown below.
•
When on a slope always stand on the uphill side of the
log. When "cutting through", to maintain complete control
reduce the cutting pressure near the end of the cut without
relaxing your grip on the chain saw handles. Don't let the
chain contact the ground. After completing the cut, wait
for the saw chain to stop before you move the chain saw.
Always stop the motor before moving from cut to cut.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
CUT FROM TOP (OVERBUCK)
AVOID CUTTING EARTH
2nd CUT OVERBUCK
(2/3 DIAMETER)
TO MEET 1st CUT
(TO AVOID PINCHING)
1st CUT UNDERBUCK
(1/3 DIAMETER)
AVOID SPLINTERING
1st CUT OVERBUCK
(1/3 DIAMETER)
TO AVOID SPLINTERING
2nd CUT UNDERBUCK
(2/3 DIAMETER)
TO MEET 1st CUT
(TO AVOID PINCHING)
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Saw Chain Sharpness
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut
you when it is not running.
IMPORTanT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail while cutting.
To get the best possible performance from your chain saw it
is important to keep the teeth of the saw chain sharp. Chain
sharpening services are available from your nearest D
service center.
nOTE: Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should be
used. It is recommended that a saw chain be sharpened no
more than four times.
C
Lubrication
Your power tool requires no additional lubrication.
D
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered by
PROTOD
WALT, have not been tested with this product,
e
use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only PROTOD
recommended accessories should be used with
this product.
Consult your dealer for further information on the
appropriate accessories.
EnGLIsh
WALT
e
WALT
e
47
Werbung
Inhaltsverzeichnis
