Herunterladen Inhalt Inhalt Diese Seite drucken

Stanley FATMAX SFMCS305 Bersetzt Von Den Originalanweisungen Seite 9

V20 lithium ion
Vorschau ausblenden Andere Handbücher für FATMAX SFMCS305:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 12
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in figure B. By
pressing the state of charge button (6a) you can easily view
the charge remaining in the battery as illustrated in figure B.
Installing and Removing the Battery Pack from the
tool
Warning! Make certain the lock-off button is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack (Fig. C)
Insert battery pack firmly into tool until an audible click is
u
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
Depress the battery release button (7) as shown in figure
u
D and pull battery pack out of tool.
Storage hook (Optional extra) (Fig. E, F)
Warning! To reduce the risk of serious personal injury, place
the Speed selector and lock off button in the lock-off position
or turn tool off and disconnect battery pack before making any
adjustments or removing/installing attachments or
accessories.
An accidental start-up can cause injury.
Warning! To reduce the risk of serious personal injury, ensure
the screw (12) holding the storage hook is secure.
Note: When attaching or replacing the storage hook (11), use
only the screw (12) that is provided. Be sure to securely
tighten the screw into the accessory attachment location.
If the hook is not desired at all, it can be removed from the
tool.
To move the storage hook, remove the screw (12) that holds
the storage hook (11) in place.
Note: Various trackwall hooks and storage configurations are
available.
Please visit our website www.stanley.eu/3 for further
information.
Assembly
Warning! Before assembly, remove the battery from the tool
and make sure that the saw blade has stopped. Used saw
blades may be hot.
(Original instructions)
Fitting the saw blade (fig. G)
Hold the tool away from the body
u
Rotate the blade clamp collar (3) in the direction shown in
u
figure G.
Insert the shank of the blade (13) fully into the blade
u
clamp collar (3).
Release the blade clamp collar and gently tug on the
u
blade to ensure blade is clamped securely.
Note: The blade can be installed with the teeth up to assist in
flush cutting.
Removing the saw blade (fig. G)
Warning! Burn hazard: Do not touch the blade and clamp
collar immediately after use. Contact with the blade may result
in personal injury.
Rotate the blade clamp collar (3) to the release position
u
.
Remove blade (13)
u
Lock-Off Button and Trigger Switch (Fig. H)
Your saw is equipped with a lock-off button (2) .
To lock the trigger switch, press the lock-off button on the
u
left. Always lock the trigger switch when carrying or storing
the tool to eliminate unintentional starting.
To unlock the trigger switch, press the lock-off button on
u
the right. Pull the trigger switch to turn the motor ON.
Releasing the trigger switch turns the motor OFF.
Warning! This tool has no provision to lock the switch in the
ON position, and should never be locked ON by any other
means.
The variable speed trigger switch will give you added
versatility. The further the trigger is depressed the higher the
speed of the saw.
Warning! Use of very slow speed is recommended only for
beginning a cut. Prolonged use at very slow speed may
damage your saw.
Correct hand position (Fig. I)
Warning! To reduce the risk of serious personal injury,
ALWAYS use correct hand position as shown.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Correct hand position requires one hand on the main handle
(8) and one hand on the hand grip (5) or one hand on the
main handle (8) with the material being cut properly clamped.
Worklight (Main figure on cover of manual)
Warning! Do not stare into worklight. Serious eye injury could
result.
There is a worklight (9) located on the end of the tool near the
shoe. The worklight is activated when the trigger switch is
depressed, and will remain on for a short time after the trigger
switch is released. If the trigger switch remains depressed, the
worklight will remain on.
ENGLISH
9

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis