Bosch Indego S 500 Originalbetriebsanleitung Seite 22

22 | English
When laying out the wire avoid angles of less than 45°. This
can affect the performance.
Display
Symbol Meaning
Back button
➊
Confirm button
➋
If the confirm button is pressed whilst mow-
ing, the mower will return to the docking
station
➌ ○ Red LED on: mower error
➍ ○ Green LED on: mower is switched on
Green LED off: The mower is inactive and
your four-digit PIN code is required for ac-
tivation.
Or the mower is shut off, the isolator switch
must be turned on and your four digit PIN
code must be entered to activate the
mower.
Note: during a software update, the green
LED and red LED will be on.
➎ Left/right button
Down/up button
➏
➐ Display with dialog screen
➑ 1 2 3 Garden number (shown when more than
one garden map in the mower memory)
Only with Indego S+ 500 and M+ 700:
Network signal present
➒
Network signal absent
The display switches into sleep mode, if no input is made for
10 minutes.
Adding a further Lawn Area (see
figure K)
To install the Indego to an additional lawn area, please follow
the instructions in the Installation Guide.
Separate lawn area with separate docking station (see
figure K, right side): The mower can be used on up to three
different lawn areas. For an additional lawn area, a separate
docking station (see figure A) and the necessary perimeter
wire and pegs are required. If a schedule or the "Bosch
AUTO" calendar function or the Bosch "SmartMowing"
functionality is set, the grass of the area it is in will be cut,
within the defined time slots.
F 016 L94 038 | (06.10.2022)
Switch off the mower when transporting it between the indi-
vidual lawn areas.
Note: software updates have to be carried out on the mower
in every docking station.
To ensure remembering which docking station belongs to
which lawn area, it is recommended to label the docking sta-
tions with the lawn area number and description when stor-
ing them for winter.
Without separate docking station: It is possible to connect
the lawn areas by placing the perimeter wire between the
two lawn areas parallel to each other as close as possible
(see figure K, top left). The additional lawn area without
docking station is not recorded in the map memory and the
mower will not use the LogiCut cutting strategy in this lawn
area without the docking station. The maximum recommen-
ded lawn area without docking station is 45/50 m
dego 500/700 models). The mower will mow until it runs
out of battery and will need to be carried back to the docking
station for charging.
Mowing
Do not let children ride the mower.
u
Press the stop button on top of the mower before lift-
u
ing. Always lift the mower by its handle. (see figure F)
Only with Indego S 500 and M 700: After successful install-
ation you can either immediately begin to mow by confirming
"Mow now" on the display, or wait for the next scheduled
cutting period, as programmed by the "Bosch AUTO" Calen-
dar Function (previous setting required).
A manual mowing schedule can also be set up according to
your specific needs.
Only with Indego S+ 500 and M+ 700: After successful in-
stallation, you can begin mowing immediately by confirming
"Mow now" on the display, or on the free Bosch Smart
Gardening App by pressing "mow". You could also set up a
programmed schedule, using the Bosch "SmartMowing"
functionality, which can also plan future cutting sessions
based on when it is forecasted to rain. You could also set up
a programmed schedule in the calendar using the display or
the Bosch Smart Gardening App.
The mower must mow a lawn area 3 times completely (do 3
full cuts) to learn the lawn area. During the learning phase,
the visual result may not be optimal.
Approximate runtimes for complete lawn area coverage us-
ing LogiCut are listed below. Please note that the runtimes
will vary depending on the lawn complexity and number of
objects within the lawn area.
2
100 m 4 h
2
500 m 16 h
2
700 m 22 h
Set a schedule with frequent repetitions. This achieves good
mowing results, the battery charge will last longer and you
avoid debris on the lawn.
2
(for In-
Bosch Power Tools