Before Starting The Equipment; Assembly - EINHELL TC-TS 820 Originalbetriebsanleitung

Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning! Always pull the power plug before
making adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
Anl_TC_TS_820_SPK1.indb 20 Anl_TC_TS_820_SPK1.indb 20
GB
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.

6. Assembly

Danger! Always pull out the power plug befo-
re carrying out any maintenance or conversi-
on work.
6.1 Fitting the saw blade (Fig. 2/3)
•
Important! Pull out the power plug.
•
Unscrew the fixing screws (20) and remove
chip bin cover (19).
•
Undo the nut (21) with a ring wrench (30) on
the nut itself and a face spanner (31) on the
saw shaft (31) to apply counter-pressure.
•
Important! Turn the nut in the direction of
rotation of the saw blade (4).
•
Remove the outer flange (22).
•
When fitting a saw blade for the first time:
Clean the mounting flange, insert a new saw
blade and retighten the flange (22).
•
When changing the saw blade: Take off the
old saw blade. Clean the mounting flange,
insert a new saw blade and retighten the
flange (22).
•
Important! Note the running direction! The
running direction of the saw blade is marked
on the blade as a direction arrow.
6.2 Adjusting the splitter (Fig. 4-6)
•
Take off the saw blade guard (2) (see 6.3).
•
Take out the table insert (6) (see 6.4).
•
Fasten the splitter (5) with the two screws
(24) (Fig. 5).
•
Adjust the splitter (5) so that the gap between
the saw blade (4) and the splitter (5) equals
3 - 5 mm (see Fig. 6).
•
The splitter (5) has to be in line with the saw
blade (4) in longitudinal direction.
•
Retighten the two screws (24).
•
The setting of the splitter has to be checked
each time after changing the saw blade.
6.3 Fitting the saw blade guard (Fig. 4)
•
Mount the saw blade guard (2) on the splitter
(5) and align.
•
Insert the screw (15) through the hole in the
saw blade guard (2) and in the splitter (5) and
secure it with the nut.
•
To dismantle, proceed in reverse order.
- 20 -
26.10.15 07:14 26.10.15 07:14