Before Starting The Equipment - EINHELL BT-SS 405 E Bedienungsanleitung

Anleitung_BT_SS_405_SPK1:_
GB
Table dimensions 410 x 253 mm
Blade length
Throat depth
Cutting height max. at 90°
Cutting height max. at 45°
Weight
Load factor:
A load factor of S2 5 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (120 W) for no longer than
the time stipulated on the specifications label (5
minutes ON period). If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Noise emission values
The sawʼs noise is measured in accordance with
DIN EN ISO 3744; 11/95, DIN EN 11201. The
machine may exceed 85 dB(A) at the workplace.
In this case, noise protection measures need to
be introduced for the user (ear-muffs).
Cutting
Sound pressure level L 82,6 dB
pA
Sound power level L 95,6 dB
WA
„The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."

5. Before starting the equipment

5.1
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the blade to run freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
10
29.08.2007 13:11 Uhr
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
127 mm
Before you connect the machine to the power
406 mm
supply, make sure the data on the rating plate is
57 mm
the same as that for your mains.
27 mm
5.2 Mounting the saw on a workbench (Fig. 2)
12 kg
1. It is better to mount the saw on a solid wood
workbench rather than on a weak plywood stand
where vibrations and noise are certain to be a
nuisance.
2. The tools and hardware needed to mount the
saw on a work bench are not supplied with the
saw. Be sure to use equipment of at least the
following size:
Item
Hex screws M8
Gaskets Ø 8 mm
Washers Ø 8 mm
Hex nuts M8
3. A sound-absorbing foam rubber mat is not
supplied with the saw. It is strongly
recommended to use such a mat, however, in
order to minimize vibrations and noise.
Idling
62,3 dB
Description:
75,3 dB
Soft foam rubber mat: 450 x 250 x 13 mm
Do not overtighten the screws. Leave enough scope
for the foam rubber mat to develop a good absorbing
effect.
Mounting the saw on a workbench, see the Figure (2)
List of components in the illustration:
A: Saw body
B: Foam rubber support
C: Worktable
D: Flat gasket
E: Washer
F: Hex nut
G: Blocking nut
H: Hex screw
5.3 Assembly
Caution! Pull out the power plug before carrying out
any maintenance and conversion work on your
fretsaw.
5.3.1 Mounting the saw blade guard and the
sawdust blower facility (Fig. 4/5/6)
Put the retention bolt (9) on the radial arm (19).
Slide the saw blade guard (10) onto the retention
bolt (9).
Insert the screw (20) through the bore hole of the
Seite 10
Quantity
4
4
4
8