DeWalt DW744XP Anweisungen Seite 20

E N G L I S H
- Risk of accidents caused by the uncovered parts of the rotating saw
blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
Package contents
The package contains:
1 Partly assembled machine
1 Rip fence
1 Mitre gauge
1 TCT saw blade
1 Upper blade guard assembly
1 Table insert
1 Blade wrench
1 Arbor wrench
1 Dust extraction adaptor
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
• Remove the saw from the packaging material carefully.
Description (fig. A)
Your DW744XP jobsite table saw has been designed to perform the four
main sawing operations of ripping, cross-cutting, bevelling and mitring
easily, accurately and safely in wood, wood products and plastics.
This unit is designed for use with a 250 mm carbide tipped blade.
A1
1 ON/OFF-switch
2 Mounting holes
3 Mitre gauge
4 Table
5 Upper blade guard
6 Table insert
7 Rip fence
8 Rip scale indicator
9 Fine adjustment knob
10 Combined elevating and bevel control wheel
11 Bevel lock lever
12 Ripping position lock lever
A2
13 Rip fence latch
14 Dust extraction adapter
15 Blade/wrench storage
16 Fence rail
17 Locking knobs
18 Fence slot
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized D WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
en - 3
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and blue is for
Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or .
For 115 V units with a power rating exceeding 1500 W, we recommend to
fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
conductor size is 1.5 mm 2 . When using a cable reel, always unwind the
cable completely.
Also refer to the table below.
Conductor size (mm 2 ) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15
Voltage Amperes Cable rating (Amperes)
230 0 - 2.0 6 6
2.1 - 3.4 6 6
3.5 - 5.0 6 6
5.1 - 7.0 10 10
7.1 - 12.0 15 15
12.1 - 20.0 20 20
Assembly and adjustment
Prior to assembly and adjustment always unplug the tool.
• The machine is fully assembled except for the blade, rip fence, upper
blade guard and table insert.
Fitting the rip fence (fig. B1 & B2)
The rip fence (7) can be installed on the left or right side of your jobsite
table saw.
• Locate the pin (19) with the slot (20) in the rip fence and align the
opening (21) with the rip fence latch (22) (fig. B1 & B2).
• Secure the rip fence by snapping both latches in place (fig. B2).
25 30 45 60
6 6 6 6
6 6 6 6
6 6 10 15
10 10 15 15
15 15 20 20
20 20 25 -
15