Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
P
r
e
p
a
r
i
n
g
f
P
r
e
p
a
r
i
n
g
f
To achieve flawless functioning of the machine, please
follow the instructions listed:
Place the saw in a place that fulfils the following conditions:
secured against slipping
−
free of vibrations
−
even
−
free of tripping hazards
−
adequate light
−
Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
− that the guard is in a proper condition
− the splitting wedge setting (see splitting wedge setting)
− that the table insert is in a proper condition
− whether the pushstick is to hand
− the saw blade for flawless condition
Do not use any cracked saw blades or such that have
changed their shape.
Do not use any saw blades made of HSS steel.
Immediately replace a worn or damaged table insert.
When sawing, place yourself to the side of the danger area
(saw blade).
Lower the guard onto the bench top
− when working on the workpiece
− when interrupting the work or leaving the saw
C
o
m
C
o
m
Rotational direction of the saw blade
Ensure that the rotational direction of the saw blade is the
same as the rotational direction given on the guard (5).
Selection of saw blades
Consider when selecting the saw blade, that no edgeless or
damaged saw bands are used and that the diameter of the
blade location hole is 30 mm.
The saw blade supplied as a standard is suitable for timber and
most plastics.
Other saw blades are available for other uses on
request. Ask your dealer or us.
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the saw to the
relevant and properly earthed plug
Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker (FI switch 30 mA).
o
r
c
o
m
m
i
s
s
i
o
n
i
n
g
o
r
c
o
m
m
i
s
s
i
o
n
i
n
g
m
i
s
s
i
o
n
i
n
g
m
i
s
s
i
o
n
i
n
g
Main fuse: 16 A inert
Use the connection or extension cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm2 for cable lengths up to 25m
2.5 mm2 for cable lengths over 25m
On / Off Switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switch on
Press the green button ( I )
on the switch.
If there is a power cut, the
machine
switches
automatically. To switch on
again, press the green ( I )
button.
Switch off
Press the red button ( 0 ) on the switch.
Motor protection
The motor is equipped with a safety switch and
switches off independently when overloaded.
It can be switched back on following cooling phase (5 -
10 min.) .
First press
1. the red button (0)
2. the small button with the clear cover (35)
3. the green button ( I ) to start
Dust/chip exhaustion
The wood dust generated during operation impedes the
necessary view and is harmful to health to some degree.
If the machine is not used in the open air, a shavings exhausts
must be attached to both exhaust outlets (e.g. small
transportable dust remover).
Chip exhaustion
Connect a chip exhaust system or small vacuum cleaner
with suitable adapter to the chip exhaust neck (32) (Ø 35 mm).
Air velocity at the exhaust neck of the saw ≥ 20 m/sec
Use a special exhaust device when exhausting dusts that are
especially harmful to health, carcinogen or dry.
off
17
Werbung
Kapitel
Inhaltsverzeichnis
