How To Fit The Group 1 (9-18 Kg) Child Car Seat To The Car With A 3-Point Seat Belt; How To Fit The Group 2 (15-25 Kg) Child Car Seat To The Car With A 3-Point Seat Belt And Top Tether - Chicco Seat Up 012 Bedienungsanleitung

seat or between the child car seat and car
door.
Push the child car seat firmly against the back-
rest of the car seat (Fig. 19) to make sure it is
securely in place.
The assembly of the child car seat is complet-
ed exclusively with the installation of the Top
Tether (T).
WARNING! Refer to your car's user manual to
identify where the Top Tether of the child car
sear is attached to the car. This fastening point
is denoted with a specific label (Fig. 20) and
can be found in the positions indicated by the
figures 21A – 21B – 21C – 21D.
WARNING! Check that the Top Tether fasten-
er used is the one that has been specially des-
ignated. Do not confuse it with a ring used for
hanging bags (Fig. 22).
WARNING! Pass the Top Tether between the
top of the car seat backrest and the headrest.
Never pass the Top Tether above the car head-
rest.
Extend the Top Tether belt by pressing adjust-
ment button (V).
Once you have identified the fastening point,
connect to the Top Tether hook (U).
Adjust the length of the Top Tether belt by
forcefully pulling the belt until it is tight. The
indicator on the belt goes green (W) when
the tether is suitably tight (Fig. 23). Roll up any
excess belt and tie up using the velcro.
To disassemble the child car seat, unhook the
Top Tether and the Isofix connectors by press-
ing the release buttons (Q) (Fig. 24). To put
them back in completely push them inwards.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
6. HOW TO FIT THE GROUP 1 (9-18 kg)
CHILD CAR SEAT TO THE CAR WITH A
3-POINT SEAT BELT
WARNING! Never fit the seat belt in any way
not mentioned in this manual.
All manuals and user guides at all-guides.com
The slots for the car seat belts are clearly
marked on the child car seat with red colour
guide items.
Position the child car seat on the selected seat.
WARNING! Make sure there are no objects
between the child car seat and the vehicle
seat or between the child car seat and car
door.
Pull the car seat belt, and slide it through the
space between the backrest and the base of
the child car seat (Fig. 25).
Pass the abdominal part of the car's 3-point
seat belt through the specific red abdominal
belt guides (M). Pull it out from the other side
of the child car seat and fasten it to the buckle
of the seat until you hear a "CLICK" (Fig. 26).
Continue to assemble on the side of the re-
tractable part of the belt. Completely insert
the belt in the red clamp (L), holding it open
(Fig. 27).
After completing the assembly it is necessary
to make the safety harness as tight as possible.
Pull the diagonal part hard towards the retrac-
tor and fasten with the red clamp (L) (Fig. 28).
WARNING! Check that the child car seat is fit-
ted firmly in place and adheres correctly to the
vehicle seat; check that the seat belt is tight. If
the child car seat is not tightly and safely fitted
into the car seat, repeat the installation.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
7. HOW TO FIT THE GROUP 2 (15-25 kg)
CHILD CAR SEAT TO THE CAR WITH A
3-POINT SEAT BELT and TOP TETHER
WARNING! Before fitting the child car seat
and seating your child, adjust the position of
the child car seat buckle (from A to B) as indi-
cated in paragraph 11. ADJUSTING THE CHILD
CAR SEAT BUCKLE.
Position the child car seat on the selected seat.
WARNING! Make sure there are no objects be-
tween the child car seat and the vehicle seat or
between the child car seat and car door.
26
Pull th
space
the ch
Pass t
seat b
belt g
of the
of the
Contin
tractab
the be
(Fig. 3
After c
to ma
Pull th
tor an
The as
ed exc
Tether
WARN
identi
sear is
is den
can be
figure
WARN
er use
ignate
hangin
WARN
top of
Never
rest.
Extend
ment
Once
conne
Adjust
forcefu
indica
the te
excess
WARN
ted fir
vehicl
the ch
into th
This ty