Initial Start-Up - Kärcher WD 5 Renovation Originalbetriebsanleitung

Flat fold filter
20
Removable handle with electrostatic protection
21
Suction hose with connection piece
22
Suction pipes 2 x 0.5 m
23
Crevice nozzle
24
Floor nozzle
25
Adapter for connecting power tools
26
Coarse dirt hose, NW 45 (renovation)
27
Coarse dirt pipes 2 x 0.5 m, NW 45 (renovation)
28
Coarse dirt floor nozzle, NW 45 (renovation)
29
Suction brush with soft bristles (workshop)
30
Flexible tool hose (workshop)
31
Mount the steering rollers and
support for the accessory holder
1. The carrying handle also serves to lock the device
head and container. To unlock, swivel the bracket all
the way forward until the lock is free.
Illustration B
2. Before initial startup, remove the contents from the
container and mount the steering rollers.
Illustration C
Illustration D
3. Clip the support for the accessory mounting on the
back of the device head.
Illustration E
Note
For versions with stainless steel tubes, remove the pro-
tective cover before initial startup.
Initial startup
Inserting the filter bag
1. Fully unfold the filter bag.
2. Attach the filter bag to the device connection and
press it on firmly.
Illustration F
3. Fit and lock the device head.
Illustration G
Installing the hose, pipes, floor nozzle
1. Connect the suction hose.
Illustration H
2. Connect the suction hose to the handle.
Illustration I
Note
For convenient vacuuming in confined spaces, the han-
dle can be removed, and the accessories plugged di-
rectly onto the suction hose.
To release the handle, the grey areas on both sides of
the handle must be pressed, and the handle pulled from
the hose.
3. Connect the floor nozzle to the suction pipes.
 Use the position with the brush strips extended to
vacuum dry dirt.
 Use the position with squeegees extended to
suck up damp dirt / water.
Illustration J
Starting up the device
1. Plug the mains plug into the socket.
Illustration K
Devices without a socket
2. Set the trigger into the desired position.
Illustration L
 Position "1 ON": The suction / blower function is
activated.
 Position "0 OFF": The device is switched off.
Devices with a socket
3. Set the trigger into the desired position.
Illustration M
 "MAX" position: The suction / blower function is
activated.
 Position MAX
nected, the suction is activated automatically.
 Position "0 OFF": The device is switched off.
Note
As long as the device is supplied with power, the device
socket can be used as a power source.
ATTENTION
Flat pleated filter missing
Device damage
Always work with the flat pleated filter inserted.
Note
Pay attention to the latest part numbers when purchas-
ing and installing filter bags and flat pleated filters.
Information on accessories and spare parts can be
found at www.kaercher.com.
ATTENTION
Vacuuming cold ashes
Device damage
Only vacuum cold ash with an ash pre-separator.
ATTENTION
Defective or wet flat pleated filter
Device damage
Before initial startup, check the flat pleated filter for
damage and replace it if necessary.
Only vacuum with a dry flat pleated filter.
Note
Replace the filter bag in good time, as a filter bag that is
too full could be damaged. The fill degree of the filter
bag depends on the amount of dirt vacuumed. The filter
bag should be replaced more frequently when vacuum-
ing fine dust, sand, etc.
ATTENTION
Wet vacuuming with a filter bag
Device damage
Do not use a filter bag when vacuuming wet.
ATTENTION
Operation with full container
When the container is full, a float switch closes the suc-
tion opening and the device runs at a higher speed.
Switch off the device immediately and empty the con-
tainer.
Note
If the device falls over, the float can also close. To make
the device capable of vacuuming again, set up the de-
vice, switch it off, wait 5 seconds and then switch it on
again.
English
: When the power tool is con-
Operation
Dry vacuuming
Wet vacuuming
9