Herunterladen Diese Seite drucken

Miche REVOX WR DX Gebrauchs- Und Wartungsanleitung Seite 7

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

ENGLISH
GENERAL INDICATIONS
1
We thank you for buying the REVOX WR DX wheels, product
that will guarantee you security and functionality through the
years.
Before proceeding with using the wheels, please read carefully
the following instruction and store them in a safe place for
eventually reusing.
In the box of wheel set you will find:
• The front wheel arranged with TX-12 system
• The rear wheel arranged with TX-12 system
• Elastic wheel protection
• The manual of instructions and use of Wheels
• Rim tapes
Caution! Only use the Miche supplied rim tapes with your
!
Miche wheels and only with the correct clincher tyre and
inner tube. The standard supplied rim tapes are not sui-
table for Tubeless Ready tyres wheels conversion.
Warning
!
Any modification or alteration (and graphic) of the product
with non-original spare parts or spare parts not delivered
directly by Fac Michelin S.r.l., involves the expiration of the
guarantee.
Warning
!
Direct and violent impacts on broken road surfaces can
cause damage to the rims. Such damage is outside the con-
ditions of our guarantee and repair costs will be charged
directly to the customer.
Warning
!
In case of strange impact caused from bad road base or
wheels transport, we trust to bring the wheels to your me-
chanic for a check.
Warning
!
Tyre width section: min 25 / max 35
Warning
!
Only Shimano original lock ring designed for through axle
internal diameter 27mm to be used with the disc brake.
Warning before using the bicycle:
• C heck for proper operation and state of wear of all the
components before starting to ride. Before any maintenan-
ce operations on your wheels, always wear gloves and
protection glasses.
• Check the condition and pressure of the tyres fitted to
your Miche wheels. Pressure must not exceed the limit of
7,5bar and 108psi signed behind valve hole. The inflating
pressure of the tyres must NOT exceed the LOWER pressure
level between the maximum pressure stated by the tyre
manufacturer.Excessive tire pressure reduces the grip of
the tire on the road and increases the risk that the tire
will unexpectedly burst.Inflation pressure that is too low
reduces tire performance and increases the probability of
sudden and unexpected loss of tire pressure. In addition,
premature damage to the rim may occur. Incorrect tire
pressure could cause tire failure or loss of control of the
bicycle, resulting in an accident, personal injury or death.
• Check the tension of the spokes so as to notice any spo-
kes which got loose. In the case spokes are loose, contact
a qualified mechanic or special personnel to perform the
tensioning.
Warning, the use of wheels not centered properly or with
spokes broken and/or loosen or damaged may cause an
accident, serious injury or death.
• Check that the wheels are firmly anchored to the frame with
the locking item closed in the correct position. If there is
the passing through pin, consult the installation instructions
provided by the manufacturer of the bicycle or fork.
Warning, an incorrect locking may cause the detachment
of the wheel and derive in accidents and serious or fatal
injuries.
• C heck that the braking system and the brake pads in the bra-
ke calipers are in good state and that the screws on the disc
or the locking ring of the disc, depending on your model, are
properly locked.
• T o the users of more than 78 kg weight, Fac Michelin S.r.l.
suggests to check the wheels status to the mechanic every
two months or every 500km.
• If the total weight of your bike and various parts installed
exceeds 109 kg, not used these wheels.
• Never wash the pieces with pressure-fed water because wa-
ter may get through the seals and cause permanent damage
to the internal components. We recommend washing compo-
nents with a sponge, mild soap, and water.
• Salt water environments (as found on winter roads and
neat the seaside) can cause galvanic corrosion on most
bike parts. Carefully rinse, clean, dry and re-lubricate
all exposed parts to avoid damage, malfunctions and
accidents.
• If your component shows signs of rust, this means it
has to be changed URGENTELY as it might be a sign of
damage.
7

Werbung

loading