Technical Data; Noise/Vibration Information - Bosch GWS 24-230 JVX Professional Originalbetriebsanleitung

A)
(22) Diamond cutting disc

Technical Data

Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Restart protection
Starting current limitation
Rotatable auxiliary handle
Run-out brake
Weight according to EPTA-Procedure 01:2014
– with low-vibration auxiliary handle
– with standard auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
When switching on power tools with starting current limitation, the voltage drops briefly. Interference with other equipment may occur in the
event of unfavourable conditions in the electricity supply. Malfunctions are not expected if the impedances in the electricity supply are below
0.25 ohms.

Noise/vibration information

Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 93 dB(A); sound power level
104 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a = 6.5 m/s , K = 1.5 m/s ,
h
Disc sanding:
2 2
a = 3.5 m/s , K = 1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
Bosch Power Tools
(23) Handle (insulated gripping surface)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 24-230 JVX
3 601 H64 Z..
W 2400
W 1600
-1
min 6600
mm 230
M 14
mm
kg
kg
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting
Fitting protective equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective Guard for Grinding
Open the clamping lever (8). Place the protective guard (6)
with the coding cam (7) engaging into the coding groove on
the spindle collar until the shoulder of the protective guard is
seated against the flange of the power tool, and turn the pro-
tective guard (6) to the required position. Close the clamp-
ing lever (8).
English | 19
GWS 24-230 JVX
3 601 H64 U..
2400
1600
6600
230
M 14
18 18
●
●
●
●
6.5 6.6
6.4 6.5
/ II
1 609 92A 5FF | (11.02.2020)
●
●
●
●
/ II