Stiga DUO LINE series Gebrauchsanweisung Seite 49

• Never use the snow thrower near enclosures, cars,
windowpanes, slopes etc. without properly setting the
discharge chute deflector.
• Always keep children away from areas to be cleared. Get
another adult to keep the children under supervision.
• Do not overload the machine by driving it too fast.
• Take care when reversing. Look behind you before and
during reversing to check for any obstacles.
• Never point the discharge chute towards bystanders. Do
not allow anyone to stand in front of the machine.
• Disengage the auger when the snow thrower is to be
transported or is not in use Do not drive too fast on
slippery surfaces when transporting.
• Only use accessories that are approved by the machine's
manufacturer.
• Never drive the snow thrower in bad visibility or without
satisfactory lighting.
• Always ensure you have a good balance and a tight grip
on the handle.
• Never use the snow thrower on a roof.
• Do not touch engine components because they are warm
during use. Risk of burn injuries.
2.4 MAINTENANCE AND STORAGE
• Tighten all nuts and screws so that the machine is in safe
working condition. Check the shear bolts regularly.
• Always use genuine spare parts. Non-genuine spare parts
can entail a risk of injury, even if they fit the machine.
• Never store the machine with petrol in the tank in
buildings where the fumes can come into contact with
open flames or sparks.
• Allow the engine to cool before putting the machine in
store.
• Before a long storage, check the instructions for
recommendations.
• Replace damaged warning and instruction stickers.
• Let the engine run a couple of minutes with the auger
connected after use. This prevents the auger from
freezing solid.
3 ASSEMBLY
Note: Instructions to the left and right sides start from the
driving position behind the snow thrower.
3.1 CONTENTS - OUTER PACKING
The packing contains:
- One snow thrower
- One adjustment lever
- Gear lever
- One discharge chute
- One set of instructions
- One assembly kit
In addition, the following are supplied:
- Chute clearing tool (15 in fig. 8)
- Extra break bolts for spare
ENGLISH
3.2 UNPACKING
1. Remove all loose items from the carton.
2. Cut the four corners of the carton and let the sides fall
down.
3. Unscrew the screws (B) that fasten the shoes to the
bedding. See fig. 1. (some models only)
4. Roll the snow thrower from the carton.
5. Cut the plastic tape holding the control wires on the
underside of the handle.
3.3 HANDLE, FIG. 2
1. Loosen the longer screws in the lower part of the handle.
2. Fold up the upper part of the handle. NOTE! Make sure
the control wires do not jam.
3. Place a screw (A) and a flat washer (B) in the lower, right
hand hole.
4. Lock with a locking washer (C) and a nut (D).
5. Remove the locking nut and washer from the eyebolt
sitting on the adjustment lever.
6. Place the eyebolt in the left upper hole.
7. Replace the washer and nut on the eyebolt.
8. Tighten all the nuts when the adjustment lever has been
assembled (see below).
3.4 ADJUSTMENT LEVER, SEE FIG. 3
1. Remove the locking pin (12).
2. Place the shaft (15) in the sleeve (16) in the toggle joint.
3. Lock the joint with the locking pin (12).
4. Check the discharge chute by turning it fully in both
directions. The chute should rotate freely.
3.5 SNOW DISCHARGE CHUTE, SEE FIG. 4
1. Turn the adjustment lever anti-clockwise until it resists.
2. Place the discharge chute (2) on the flange until the holes
meet.
3. Mount the three carriage bolts (1) from the inside.
4. Mount the washers (5) and locking nuts (6) on the outside
of the flange.
5. Tighten properly.
3.6 CONTROL KNOBS, FIG. 5
1. Screw the nut (J) onto the gear lever.
2. Mount the control knob (K) onto the gear lever.
3. Tighten the nut on the underside of the control knob.
3.7 CHECKING THE CONTROL WIRES
The control wires might need adjusting before using the
snow thrower for the first time.
See ADJUSTING THE CONTROL WIRES below.
3.8 TYRE PRESSURE
Check the air pressure in the tyres. Correct air pressure: 1.0
– 1.2 bar.
EN
49