Herunterladen Inhalt Inhalt Diese Seite drucken

Unpacking; Assembly - Scheppach 5906149701 Original Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Theo. intake capacity
Effective delivery quantity
Protection category
Device weight
Oil (15W 40)
Max. installation altitude (above
sea level)
Belt type
Technical changes reserved!
Noise and vibration
m Warning: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A), please
wear suitable hearing protection.
Noise data
Sound power level L
WA
Sound pressure level L
pA
Uncertainty K
wa/pA

8. Unpacking

• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With
accessories
as
and replacement parts use only original parts.
Replacement parts can be obtained from your dealer.
• When ordering please provide our article number
as well as type and year of manufacture for your
equipment.
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with
plastic bags, films or small parts! There is a
danger of choking or suffocating!
26 | GB
550 l/min
350 l/min
IP32
80 kg
1,2 l
1000 m
A-1400
97 dB(A)
84,6 dB(A)
2,39 / 3 dB(A)
well
as
wearing
parts
www.scheppach.com
9.

Assembly

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
You require the following for assembly:
• Open-ended spanner 12 mm (not included in the
scope of delivery)
• Open-ended spanner 14 mm (not included in the
scope of delivery)
• Open-ended spanner 17 mm (not included in the
scope of delivery)
• Allen key 4 mm (not included in the scope of supply)
• Cross-screwdriver (not included in the scope of
supply)
9.1 Fitting the wheels (Fig. C)
Insert the screw (23) through the wheel (14). Now insert
the screw (23) through the mount on the pressure
vessel (12). Now insert the screw (23) with the nut (24).
Repeat the process on the other side of the pressure
vessel (12).
9.2 Fitting the foot (2x) (Fig. D)
Insert the screw (25) through the foot (13). The foot (13)
is subsequently fitted on the mount on the pressure
vessel (12).
Fasten the foot (13) with the nut (26).
Repeat the process for the second foot.
9.3 Fitting the air filter (3x) (Fig. E)
Remove the transport protection from the air filter
mount (if applicable).
Remove the wing nut (27) and washer (28) from the
threaded pin on the compressor pump.
Fit the air filter housing (1) with the paper filter on the
threaded pin. Refasten the air filter housing (1) with the
washer (28) and wing nut (27).
Repeat the process with all air filters.
Fasten the air filter with the inlet opening facing
downwards, to avoid excessive contamination.
9.4 Fitting the transport handle (Fig. F)
Fasten the transport handle (6) to the pressure vessel
(12) with the screw (29) as shown.
Repeat this process three times.

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Hc550tc 230v

Inhaltsverzeichnis