Makita M3602 Betriebsanleitung Seite 11

Straight guide
The straight guide is effectively used for straight cuts
when chamfering or grooving.
Straight guide (Type A)
Optional accessory
Install the straight guide on the guide holder with the
thumb screw (B). Insert the guide holder into the holes
in the tool base and tighten the thumb screw (A). To
adjust the distance between the router bit and the
straight guide, loosen the thumb screw (B) and turn the
fine adjusting screw. At the desired distance, tighten the
thumb screw (B) to secure the straight guide in place.
► Fig.10: 1. Guide holder 2. Fine adjusting screw
3. Straight guide
Straight guide (Type B)
Optional accessory
Insert the straight guide into the holes in the tool base
and tighten the thumb screw. To adjust the distance
between the router bit and the straight guide, loosen the
thumb screw. At the desired distance, tighten the thumb
screw to secure the straight guide in place.
► Fig.11: 1. Thumb screw 2. Straight guide
When cutting, move the tool with the straight guide flush
with the side of the workpiece.
Wider straight guide of desired dimensions may be
made by using the convenient holes in the guide to bolt
on extra pieces of wood.
When using a large diameter router bit, attach pieces
of wood to the straight guide which have a thickness of
more than 15 mm (5/8") to prevent the router bit from
striking the straight guide.
► Fig.12: 1. Straight guide 2. Wood
A=55 mm (2-3/16")
B=55 mm (2-3/16")
C=15 mm (5/8") or thicker
Templet guide
Optional accessory
The templet guide provides a sleeve through which the router
bit passes, allowing use of the router with templet patterns.
► Fig.13
1.
Loosen the screws on the base, insert the templet
guide and then tighten the screws.
► Fig.14: 1. Screws 2. Templet guide
2. Secure the templet to the workpiece. Place the
tool on the templet and move the tool with the templet
guide sliding along the side of the templet.
► Fig.15: 1. Router bit 2. Base 3. Base plate
4. Templet 5. Workpiece 6. Templet guide
NOTE: The workpiece will be cut a slightly different
size from the templet. Allow for the distance (X)
between the router bit and the outside of the templet
guide. The distance (X) can be calculated by using
the following equation:
Distance (X) = (outside diameter of the templet
guide - router bit diameter) / 2
Trimmer guide
Trimming, curved cuts in veneers for furniture and the
like can be done easily with the trimmer guide. The
guide roller rides the curve and assures a fine cut.
Trimmer guide (Type A)
Optional accessory
Install the trimmer guide on the guide holder with the
thumb screw (B). Insert the guide holder into the holes
in the tool base and tighten the thumb screw (A). To
adjust the distance between the router bit and the
trimmer guide, loosen the thumb screw (B) and turn the
fine adjusting screw. When adjusting the guide roller up
or down, loosen the thumb screw (C). After adjusting,
tighten all the thumb screws securely.
► Fig.16: 1. Guide holder 2. Fine adjusting screw
3. Trimmer guide 4. Guide roller
Trimmer guide (Type B)
Optional accessory
Install the trimmer guide onto the straight guide using
the thumb screws (B). Insert the straight guide into the
holes in the tool base and tighten the thumb screw (A).
To adjust the distance between the router bit and the
trimmer guide, loosen the thumb screws (B). When
adjusting the guide roller up or down, loosen the thumb
screw (C). After adjusting, tighten all the thumb screws
securely.
► Fig.17: 1. Guide roller 2. Trimmer guide
When cutting, move the tool with the guide roller riding
the side of the workpiece.
► Fig.18: 1. Router bit 2. Guide roller 3. Workpiece
Dust cover (For tool with the knob)
Optional accessory
Dust cover prevents sawdust from being drawn into the
tool in the inverted position.
Install the dust cover as illustrated when using the tool
with a router stand available in the market.
Remove it when using the tool in the normal position.
► Fig.19: 1. Screw 2. Dust cover
Spacer (For tool with the knob)
Optional accessory
The spacer prevents the router bit from dropping into
the chuck when replacing the router bit in the inverted
position.
Insert the spacer as illustrated when using the tool with
a router stand available in the market.
► Fig.20: 1. Collet nut 2. Collet cone 3. Spacer
11 ENGLISH