Installation Instructions; Intended Use; Approval; Tools And Facilities Required - Truma Mover SE R Gebrauchsanweisung

Installation instructions

Before commencing any work, read and observe the installa-
tion instructions carefully!
Please ensure that no metal chips or other contaminants get
into the controller during installation.

Intended use

The Mover® SE R is designed for use on single-axle caravans
with a gross weight of up to 2000 kg,
and the Mover® TE R is designed for use on dual-axle cara-
vans with a gross weight of up to 2250 kg.
The Mover® SE R / TE R weighs approx. 33 kg.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.

Approval

The Truma Mover® SE R / TE R has design approval, and a
general operating permit (ABE) has been issued for Germany.
Acceptance by a vehicle expert is not required (except when
installing the flat frame kit). The ABE must be kept in the
vehicle.
The Mover® satisfies other requirements stated in the EC di-
rectives and standards (see declaration of conformity).
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover® is being installed.
Any modifications to the unit or the use of spare parts and
accessories that are important to the operation of the system
that are not original Truma parts and failure to follow the in-
stallation and operating instructions will cancel the warranty
and indemnify Truma from any liability claims. In addition to
this, the operational approval for the device will be cancelled.

Tools and facilities required

To install the unit you will need:
– 13 mm, 17 mm socket wrench, ring spanner or
open-jawed spanner
– Torque wrench (5 – 50 Nm)
– Cable cutter / Crimping tool
– Power drill / screwdrivers / 25 mm hole cutter
– Portable 2 tonne trolley jack and axle stands to suit
– Appropriate lighting
20

Minimum installation dimensions

A distinction is made between L-profiled and U-profiled
chassis as shown in the illustration.
Caravan floor
L-profi i le
The equipment can only be fitted to caravans / trailers within
the following dimensions.
Caravan floor
170
min. 25
min. 35 **
min. 50
min. 1200 / max. 2000
max. 2400
All dimensions in mm.
* for a loaded vehicle with a max. allowed gross weight
** for U-profile

Measuring the chassis height

A frame height of min. 170 mm is required about 330 mm
from the outer edge of the tyre at the height of the wheel
hub / centre.

Determining the installation type

1. Standard installation
Standard installation for chassis with a U or L-profile and a
frame height of min. 170 mm. No special accessories are
required.
2. Installation in a chassis with a U or L-profile and
frame height between 110 mm and less than 170 mm
The spacer set 30 mm (up to 140 mm frame height) or spacer
set 60 mm (less than 140 mm frame height) is required to
compensate the height difference.
3. Installation with chassis with U-profiles or L-profiles
with frame height of less than 110 mm
A low chassis kit needs to be used to compensate the
height difference for chassis with a height of less than
110 mm.
In Germany, the low chassis kit installation must
be accepted by a vehicle expert.
4. The AL-KO Vario III / AV installation kit must be used
with the AL-KO Vario III / AV chassis with a frame thickness of
less than 2.8 mm.
4a. For mounting in front of the axle on the AL-KO chas-
sis M, with sliding rails
The AL-KO Chassis M Adapter set needs to be used to
compensate the overlapping frame edges.
5. Installation with Eriba Touring chassis
The Eriba Touring mounting set is needed for the Eriba Touring
chassis.
U-profile
min. 170
330