Technical Data; Before Starting The Equipment - Parkside PKS 1500 B3 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

7. Technical data

AC motor.....................................................220 - 240 V ~ 50Hz
Power S1 .....................................................................1200 Watt
Operating mode ............................................ S6 25%* 1500W
Idle speed n .............................................................. 5000 min
0
Carbide saw blade ...............................ø 210 x ø 30 x 2,6 mm
Number of teeth .......................................................................48
Maximum saw blade tooth width ...................................... 3 mm
Swivel range ................................................... -45° / 0°/ +45°
Mitre cut ........................................................0° - 45° to the left
Saw width at 90° ................................................. 120 x 60 mm
Saw width at 45° ....................................................80 x 60 mm
Saw width at 2 x 45°
(double mitre cut) .....................................................80 x 35 mm
Protection class .................................................................... II /
Weight ......................................................................... ca. 7,6 kg
Laser class ................................................................................... 2
Wavelength of laser ........................................................ 650 nm
Laser output .....................................................................< 1 mW
* S6, continuous operation periodic duty. Identical duty cycles
with a period at load followed by a period at no load. Running
time 10 minutes; duty cycle is 25% of the running time.
The work piece must have a minimum height of 3
mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Noise
Total noise values determined in accordance with EN 62841.
Sound pressure level L ............................................ 99,6 dB(A)
pA
Uncertainty K ......................................................................3 dB
pA
Sound power level L ............................................112,6 dB(A)
WA
Uncertainty K .....................................................................3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing
The above-mentioned noise emission values were measured in
accordance with a standardised test procedure and can be
used to compare one power tool with another.
The above-mentioned noise emission values can also be used
for the preliminary assessment of exposure.
Warning:
• The noise emissions during the actual use of the power tool
may differ from the above-mentioned values depending on
the power tool being used, in particular on the type of work-
piece being processed.
• Try to keep emissions as low as possible, for example by
limiting your working time. In this regard, all the operational
cycle phases must be taken into consideration (such as the
times when the tool is switched off or running idle).
8 GB/IE

8. Before starting the equipment

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
-1 • Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
Always ensure that the machine is stable and can
stand securely, i. e. bolted down on a workbench.
• The equipment must be set up where it can stand securely.
Secure the machine on a workbench or a base frame with 4
screws (not included in delivery) using the holes on the fixed
saw table (9).
• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply make
sure the data on the rating plate are identical to the mains
data.
8.1 Assembling the work piece clamping device
(fig. 2)
• Loosen the locking screw (19) and attach the work piece
clamping device (15) to the left or right of the fixed saw
bench.
• Afterwards, retighten the locking screws (19).
8.2 Assembling the work piece supports
(fig. 2 - 3)
• Loosen the locking screw (14) and guide the work piece
support through the specified hole on the side of the fixed
saw bench.
• Make sure that the work piece support (18) is also guided
through the two plates on the underneath.
• Afterwards, retighten the locking screw (14).
• Repeat this process on the other side.
8.3 Assembling the support stand (fig. 2 - 3)
• Loosen the locking screw (20) on the underneath of the saw
and guide the support stand (21) through the specified holes
on the back of the saw.
• Afterwards, retighten the locking screw (20).