Operation - Scheppach DECO-XLS Bedienungsanleitung

1. Loosen the locknut of the adjustment screw (37).
2. To set the saw table, use a 90° bracket (31, not in
the scope of delivery). Place this against the saw
table and the saw blade (fig. 12).
3. Adjust the adjustment screw (37) until the angle
between the saw blade (22) and the saw table
(6) is 90°.
4. Tighten the locknut of the adjustment screw (37)
again.
5. Loosen the screw (32) and turn the pointer (33)
to the 0° marking.
6. Make a test cut. Check the angle on the work-
piece with a protractor. If necessary, readjust the
pointer (33).
8.4 Installing the blow-off device (fig. 8)
1. Ensure that the saw blade guard (5) folded down.
2. Screw the blow-off device (1) clockwise onto the
holder (2) as described in fig. 8.
8.5 Installing the depressor (fig. 6, 7)
NOTE:
Before assembling the depressor (24), the saw blade
pre-installed at the factory (22) must be removed (see
8.1.3).
1. Remove the saw blade (22) as described in
8.1.3.
2. Remove the depressor (24) from the saw blade
guard (5) by loosening the screw (25) completely
(see fig. 6).
3. Insert the holder (4) into the opening (see fig. 7).
4. Fasten the holder (4) with the knurled screw (3).
5. Install the depressor (24). Insert the screw (25)
into the holder (4) and fasten it.
6. Insert the saw blade (22) again as described in
8.1.3.
7. Ensure that the depressor (24) does not contact
the saw blade (22).
The depressor (24) must always be adjusted accord-
ing to the workpiece height. However, the workpiece
should not be clamped, but should rather be able to
move freely.
The depressor (24) is used to lock the workpiece so
that it cannot swing upwards, which would destroy the
saw blade (22).
8.6 Chip extraction (fig. 13)
ATTENTION: Only operate the device with an extrac-
tion system.
Connect a suitable chip extraction system (not includ-
ed in the scope of delivery) to the suction connection
(15) (see fig. 13, sample figure).
ATTENTION: Check and clean the suction channels
at regular intervals.

9. Operation

9.1 General information
• The saw does not cut wood automatically. Rather,
the operator must push and guide the wood toward
the moving saw blade.
• The teeth only cut the wood on the downstroke.
• The wood must be slowly pushed and guided to-
ward the saw blade, since the teeth of the blade
are very small.
• Those who want to use the saw must go through
the process of learning how to do so. During this
time, a few blades will invariably break.
• When cutting thicker wood, special attention must
be paid not to bend or twist the saw blade.
• Handling the saw blade properly increases its ser-
vice life.
9.2 On/off switch (16)
• Switching on: Press the "I" button.
• Switching off: Press the "0" button.
ATTENTION
The machine is equipped with a safety switch against
reactivation if the voltage drops.
If the scroll saw is switched on and the power sup-
ply in the mains is interrupted, the scroll saw remains
switched off, even if the power supply is re-estab-
lished. Press the "I" button to switch it on.
9.3 Work lamp operation (fig. 4)
1. Switch the machine on as described in 9.2.
2. The work lamp (20) may not be switched on/and
off with the work lamp on/off switch (21).
9.4 Stroke rate controller (fig. 2)
The stroke rate controller (18) allows you to set the
stroke rate according to the material to be cut. In case
of soft material, we recommend high stroke rates,
while strokes rates should be kept low for hard mate-
rial. Turn the stroke rate controller (18) clockwise to
increase the stroke rate. Turning anti-clockwise low-
ers the stroke rate.
9.5 Operating modes (fig. 1, 2)
The scroll saw is able to be operated manually or via
the foot pedal.
www.scheppach.com
GB | 27