Technical Specifications; Materials Used; Electric Motor And Temperature Sensors; Electric Cable - DRENO Compatta PRO Gebrauchs- Und Wartungsanleitung

4. Technical specifications

4 .1 Materials used

The materials used to manufacture the components have been very carefully selected to ensure high reliability
and a long life even in heavy duty conditions and also to comply with the ATEX requirements and regulation
2014/34/UE and accordingly with the CEI EN 60079-0 and CEI EN 60079-1 rules. The parts that compose
the Series Compatta PRO, Alpha V PRO, AM-AT, BIC PRO, GX, electropumps are: motor case, intermediate
flange, pump body and cast iron impeller GG 25, steel motor shaft AISI 420, screws and bolts in AISI 304,
steel cable gland in AISI 304, nitrile rubber O-Rings, neoprene rubber cable gland 50sh, and steel handle AISI
304. The grinding section of GX series is in hardened steel. All the materials assembled are laboratory tested
on fitted pumps and have passed the ATEX laboratory tests, see paragraph 1. The upper and lower bearings
are single crown radial bearing. The bearings are pre-greased and should be replaced after lengthy working
periods if worn and only by qualified DRENO POMPE engineers.

4 .2 Electric motor and temperature sensors

The electric motors are asynchronous, 2 poles, single-phase or three-phase, with squirrel-cage rotor. For
230 V single-phase voltages, powers range from 0,9 to 1,5 kW, while for 400V three-phase voltages, powers
range from 0,9 to 2,2 kW. (refer to the table par. 5). The frequency is 50 Hz. (60 Hz available on request). These
motors have been designed to deliver the highest rated voltage with a variation of up to 5% of the rated volt-
age. All stators have been designed with insulation class F (155°C) and protection degree IP 68; they can be
used with fluid temperatures of 0÷40°C. Single-phase and three-phase windings are fitted with safety micro-
thermostats to prevent the motor exceeding the fixed temperature limit of 130°C. The micro thermostats are
bimetallic switches inserted in the windings, normally closed and at temperatures exceeding 130°C they
open disconnecting the power supply to the electric pump. When these safety devices have cooled (75°C),
the power supply to the electric pump returns. The electric motor is cooled by the same liquid in which the
electric pump is submerged. A maximum of 15 regolarly spaced start-ups/hour are allowed.

4 .3 Electric cable

The standard supplied electric cable is of 10 metres length.
The single-phase electropumps are supplied completed with electric control panel, whereas the three-phase mo-
tor ones of the series are provided with free terminals.

4 .4 Mechanical Seals

The Compatta PRO, Alpha V PRO, AM-AT, BIC PRO, GX electropumps are supplied with two seals, in the
series GX, AM-AT 50/2/110 C.225-226 the seals are lubricated in the oil chamber;
the upper mechanic seal is a lip seal, whereas the lower mechanical seal is made in silicon carbide + viton.

4 .5 Impellers

The impeller installed on the pumps is made in Cast Iron G20. A balancing process is conducted on all
impellers to guarantee perfect functionality in terms of minimising noise, vibration and working efficiency.
VORTEX TWIN CHANNEL
Compatta PRO -
Alpha V PRO AM/AT - BIC PRO
DNA -EX
GRINDER TWIN CHANNEL S-FLOW
GX DNB -EX
- 24

5 . Technical data

R.P.M
DN Free
Tipo
Passage
min-1
Compatta PRO
Compatta PRO (*) 50-2/060 M/T
Compatta PRO (*) 50-2/080 M/T
Compatta PRO (*) 50-2/110 M/T G2" 50 mm 2850
Compatta PRO (*) 50-2/150 M/T
Compatta PRO (*) 50-2/220 T
Alpha V PRO
Alpha V PRO (*) 50-2/060 M/T
Alpha V PRO (*) 50-2/080 M/T
Alpha V PRO (*) 50-2/110 M/T G2" 50 mm 2850
Alpha V PRO (*) 50-2/150 M/T
Alpha V PRO (*) 50-2/220 M/T
BIC PRO
BIC PRO (*) 50-2/150 M/T
G2" 20x10 2850
BIC PRO 50-2/220 T
AM-AT
AM/AT (*) 50/2/110 C.225
20x10
G2" 2850
AM/AT (*) 50/2/110 C.226
GX
GX (*) 50-2/090 M/T
GX (*) 50-2/110 M/T
G2" - 2850
GX (*) 50-2/150 M/T
GX (*) 50-2/220T
DNA-EX
DNA-EX 50-2/110 M/T
50 mm
DNA-EX 50-2/150 M/T
2850
DNA-EX 50-2/220 T 50
DNA-EX 50-2/220-1 T
1450
DNA-EX 50-4/090 M/T
DNA-EX 65-2/110 M/T
65 65 mm 2850
DNA-EX 65-2/150 M/T
DNA-EX 65-2/220 T
DNA-EX 80-2/110 M/T
DNA-EX 80-2/150 M/T 2850
80 80 mm
DNA-EX 80-2/220 T
1450
DNA-EX 80-4/090 M/T
DNB-EX
DNB-EX 65-2/080 M/T 65
65
DNB-EX 65-2/110 M/T
DNB-EX 65-2/150 M/T
50 mm
DNB-EX 65-2/220 T
65
2850
DNB-EX 65-2/220-1 T
DNB-EX 65-2/220-2 T
DNB-EX 80-2/150 M/T
DNB-EX 80-2/220 T
80 70 mm
DNB-EX 80-2/220-1 T
1450
DNB-EX 80-4/110 M/T
(1) Cable H07RN8F 4x1.5+2x0.50 Ø12 Standard version,
Absorption
Power
1 -FASE 3 -FASE Cavo
kW Hp
230 V µ F 400 V
Note (*) : The model certified ATEX is followed by the suffix «-Ex»
0,6 0,8 4,8 20 2,1
0,8 1,0 6,0 25 2,4
1,1 1,5 7,4 30 2,7
1,5 2,0 9,6 40 3,7
2,2 3,0 - - 5,2
Note (*) : The model certified ATEX is followed by the suffix «-Ex»
0,6 0,8 - - 2,1
0,8 1,0 4,8 20 2,4
1,1 1,5 6,0 25 2,9
1,5 2,0 9,6 30 3,7
2,2 3,0 - - 5,2
Note (*) : The model certified ATEX is followed by the suffix «-Ex»
1,5 1,5 8,8 40 3,5
2,2 3 - - 5,3
Note (*) : The model certified ATEX is followed by the suffix «-Ex»
1,1 1,5 6,2 25 3
1,5 2 9,6 40 3,5
Note (*) : The model certified ATEX is followed by the suffix «-Ex»
0,9 1,2 5,5 25 2,3
1.1 1,5 8,0 30 3,1
1.5 2 9,9 35 3,6
2.2 3 - - 5
1,1 1,5 7,8 30 2,9
1,5 2,0 9,9 32 3,6
2,2 3,0 - - 5,3
2,2 3,0 - - 5,3
0,9 1,2 4,7 20 2,5
1,1 1,5 7,4 30 2,7
1,5 2,0 9,9 32 3,4
2,2 3,0 - - 5,2
1,1 1,5 7,4 30 2,8
1,5 2,0 9,9 32 3,6
2,2 3,0 - - 5,2
1,1 1,5 5,2 18 2,6
0,8 1,0 5,2 18 2,1
1,1 1,5 7,5 30 2,8
1,5 2,0 9,9 32 3,7
2,2 3,0 - - 5
2,2 3,0 - - 5,3
2,2 3,0 - - 5,3
1,5 2,0 9,9 32 3,7
2,2 3,0 - - 5,5
2,2 3,0 - - 5,3
1,1 1,5 7,6 35 3,2
- 25
Kg
22
(1)
24
25
25,5
(1)
30
28
29
(1)
26
25
(1)
26
25
(1)
34
28
29
30
30
30
28
(1)
30
30,5
32
34,5
35
38
21
29
31
35
36
(1)
36
32,5
34,5
35
36