Technical Data; Attachment And Operation - Scheppach CSE2500 Original Bedienungsanleitung

• Use a surge protector with a release current of
30 mA or less.
• Have your power tool serviced by a qualified repair
person using only identical replacement parts.
• Carefully follow the maintenance, control and ser-
vice instructions in this manual.
• Practise using the saw (sawing logs on a saw-
horse) and get an experienced user or a specialist
to explain to you the function of the saw, the way of
working, the techniques of sawing and the personal
protection equipment.

6. Technical data

Cutting data chainsaw
Cutting lenght
Bar lenght
Capacity oiltank
Type of oil
Saw chain division
Drive link thickness
Saw chain type
Number of teeths drive
sprocket
Tooth pitch of drive sprocket
Chain brake
Guide bar type
Engine
Motor
Power
Cutting speed max.
Weight
Weight without bar and chain
Subject to technical changes!
Information concerning noise emission measured
according to relevant standards:
Sound pressure L = 93 dB(A)
pA
Sound power L = 104,6 dB(A)
WA
Guaranteed Sound power L
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A (front handle) = 7,5 m/s
hv
Vibration A (rear handle) = 7,5 m/s
hv
Uncertainty K = 1,5 m/s
2
PA
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
45,5 cm
45,7 v
0,125 l
wear resistant oil
3/8"
1,27 mm
Oregon
91PX062X
6
3/8"
yes
Oregon
180SDEA041
230-240 V / 50 Hz
2400 W
14 m/s
5,5 kg
4,8 kg
= 106 dB(A)
2
2
• The specified vibration emission value has been
measured according to a standardised testing pro-
cedure and can be used for comparison of one
electric tool with another;
• The specified vibration emission value can also be
used for an initial assessment of the load.
Warning:
• The vibration emission value can vary from the
specified value during the actual use of the elec-
tric tool, depending on the type and the manner in
which the electric tool is used;
• Try to minimise stress from vibrations as low as
possible. Some examples of means for reducing
the vibration stress are wearing gloves while us-
ing the tool and limiting work time. In the process
all parts of the operating cycle must be taken into
account (such as times in which the electric tool is
switched off or time in which it is switched on, but is
not running under a load).

7. Attachment and operation

Warning!
Always wear safety goggles, ear muffs, protective
gloves and heavy-duty work clothes! Use the saw
only with approved extension cables with the pre-
scribed insulation and connections designed for out-
door use (approved rubber-sheathed cables) which fit
the chainsaw plug.
The chain saw is equipped with safety switches, re-
quiring the use of both hand. The chainsaw works
only when one hand is pushing the button 11 and 13
at the same time. If the chainsaw does not run, the
chain brake must be released at the front finger guard
(3). Be sure to read the sections "Chain brake" and
"Releasing the chain brake " on this point.
To switch on:
• Release the chain brake (3), push in the lock (11)
and press the power switch (13).
• Place the lowest claw (Fig 2, J) on the wood . Raise
the chain saw by the rear grip (1 ) and saw into the
wood. Move the chain saw back a little and place
the claw further down.
• Be careful when sawing splintered wood as pieces
of wood may be ripped off.
After switching on, the chainsaw will run immediately
at high speed .
To switch off
• Release either the ON/OFF switch (13) on the rear
grip.
• The release of ON/OFF switch results the stop of
the chainsaw within 1sec., and heavy sparkling.
This is normal and safe for the proper operation of
the chainsaw.
GB | 29