Option1 Settings Menu; Setting The On-Screen Menu; Setting The Bnc Input Connector Type; Setting The Rgb1 Connector - NEC PlasmaSync 42XM4 Benutzerhandbuch

Option1 Settings Menu

Setting the on-screen menu

This sets the position of the menu, the display format
(horizontal or vertical) etc.
Example: Turning the DISPLAY OSM off
On "OPTION1" menu, select "OSM", then press the MENU/
ENTER button.
The "OSM" menu appears.
On "DISPLAY OSM" of "OSM" menu, select "OFF".
OSM
DISPLAY OSM
OSM ADJ.
OSM ANGLE
OSM ORBITER
OSM CONTRAST
SEL. ADJ.
Information
DISPLAY OSM settings
ON: The informations on screen size, volume control,
etc. will be shown.
OFF: The informations on screen size, volume control,
etc. will not be shown.
The DISPLAY button on the remote control will not
function either.
OSM ADJUST settings
Adjusts the position of the menu when it appears on
the screen.
The position can be set between 1 to 6.
OSM ANGLE settings
Sets the display format (landscape "H" or portrait "V").
When the unit is installed vertically set the OSM
ANGLE at "V".
"H"
OPTION 1 1 / 4
OSM
BNC INPUT : RGB
D-SUB INPUT : RGB
RGB SELECT : AUTO
HD SELECT : 1080B
INPUT SKIP : OFF
ALL RESET : OFF
NEXT PAGE
SEL. OK RETURN
MENU/ENTER EXIT
OSM ORBITER settings
ON: The position of the menu will be shifted by eight
dots each time OSM is displayed.
OFF: OSM will be displayed at the same position.
OSM CONTRAST settings
NORMAL: OSM brightness is set to normal.
LOW: OSM brightness is set to lower.
: OFF
: 1
: H
: OFF
: LOW
EXIT RETURN
"V"
OPTION1
OSM
BNC INPUT
: RGB
D-SUB INPUT
: RGB
RGB SELECT
: AUTO
HD SELECT
: 1080B
INPUT SKIP
: OFF
ALL RESET
: OFF
1024 768
SEL. MENU/ENTER OK
EXIT RETURN
En-23

Setting the BNC input connector type

Select whether to set the input of the 5 BNC connectors to
RGB, Component or SCART1,2.
Example: Set the BNC INPUT mode to "COMP."
On "BNC INPUT" of "OPTION1" menu, select "COMP.".
OPTION 1
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
: AUTO
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL. ADJ.
Information
BNC INPUT Settings
RGB: Use the 5BNC terminals for RGB input.
COMP.: Use the 3BNC terminals for component input.
SCART1: Use the 4BNC terminals for RGB with
composite sync. See page En-9.
SCART2: Use the 3BNC terminals for RGB and the
VIDEO1 terminal for composite sync. See page En-9.

Setting the RGB1 connector

Select one of the signals being transmitted to the RGB1
terminal.
Example: Set the D-SUB INPUT mode to "SCART3"
On "D-SUB INPUT" of "OPTION1" menu, select
"SCART3".
OPTION 1
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
: AUTO
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL. ADJ.
Information
D-SUB INPUT Settings
RGB: Use the D-SUB terminal for RGB input.
SCART3: Use the D-SUB terminal for RGB signal fed
from SCART. See page En-9.
Setting a computer image to the correct RGB
select screen
With the computer image, select the RGB Select mode
for a moving image such as (video) mode, wide mode or
digital broadcast.
Example: Setting the "RGB SELECT" mode to
"852 480 "
On "RGB SELECT" of "OPTION1" menu, select
"852 480".
OPTION 1
OSM
BNC INPUT
D-SUB INPUT
RGB SELECT
: 852 480
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL. ADJ.
1 / 4
: COMP.
: RGB
: 1080B
: OFF
: OFF
EXIT RETURN
1 / 4
: RGB
: SCART3
: 1080B
: OFF
: OFF
EXIT RETURN
1 / 4
: RGB
: RGB
: 1080B
: OFF
: OFF
EXIT RETURN