Balluff IO-Link BES M12MG1-YIC60B-S04G Betriebsanleitung Seite 53

BES M12M_1-YIC_0_-S04G
Inductive sensors
8
IO-Link interface: Parameters, commands and events (continued)
8.5 Device specific parameters
Index Name Subindex
(dec) (dec)
Proximity value
0x00B2 Proximity 0x01 (1)
(178)
Pin Configuration
0x00BC Pin 0x01 (1)
(188) Function
Selection
0x02 (2)
0x00B4 Output 0x01 (1)
(180) Type
0x02 (2)
0x00B5 Output 0x01 (1)
(181) Function
0x02 (2)
Counter function / frequency monitor
0x00B6 Switch 0x01 (1)
(182) Counter
Settings
0x02 (2)
0x03 (3)
0x04 (4)
0x05 (5)
0x06 (6)
0x07 (7)
0x08 (8)
0x00B7 Switch 0x01 (1)
(183) Counter
State
0x02 (2)
0x00BA Physical 0x00 (0)
(186) Input
Debounce
0x01 (1)
0x02 (2)
For PIN 4 the setting options are only relevant in SIO mode (in IO-Link mode PIN 4 is automatically responsible for IO-Link communication). The pin configura-
1)
tion can first be changed via IO-Link for then operating the sensor with the new configuration in SIO mode.
Tab. 8-5: Device-specific parameters
www.balluff.com
Name Data format
(length)
Current analog UINT16
C/Q (PIN 4) UINT8
1)
DIO (PIN 2) UINT8
C/Q (PIN 4) UINT8
1)
DIO (PIN 2)
C/Q (PIN 4) UINT8
1)
DIO (PIN 2)
Mode UINT8
Limit UINT16
Debounce Time UINT16
Startup Delay UINT8
UpperLimit High UINT16
UpperLimit Low UINT16
LowerLimit High UINT16
LowerLimit Low UINT16
Status UINT8
CountValue UINT16
Physical Input UINT16[]
Debounce
PIN Function UINT16
(PIN 4/CQ)
PIN Function UINT16
(PIN 2/DIO)
Access Value range
Proximity value RP in [OHM]
RW 0x00 (0) = Sensor Output
(default)
0x01 (1) = Not used.
0x02 (2) = Counter Output
0x00 (0) = Sensor Output
0x01 (1) = Teach-in Input
(default)
0x02 (2) = Counter Output
0x03 (3) = Counter Reset
RW 0x00 (0) = Disabled
0x01 (1) = PNP
0x02 (2) = NPN
0x03 (3) = Push-Pull (default)
RW 0x00 (0) = NO (default)
0x01 (1) = NC
RW 0x00 (0) = Inactive (default)
0x01 (1) = STATIC
0x02 (2) = AUTO
0x03 (3) = SPEED
0x0000...0xFFFF (0...65535) Counts (0 =
0x0000...0xFFFF (0...65535) ms (0 = not
0x00...0xFF (0...255)
0x0000...0xFFFF (0...65535) Hz (0 = not
0x0000...0xFFFF (0...65535)
0x0000...0xFFFF (0...65535)
0x0000...0xFFFF (0...65535)
RW Bit 0: Count limit / Speed ok
Bit 1: Speed too low
Bit 2: Speed too high
0x0000...0xFFFF (0...65535) Counts or Hz
RW
0 (default) / No input support
300 (Default) / 0...65535 ms
Description
In SIO mode
In SIO mode
In SIO mode
not active,
default)
active, default)
s (0 = not
active, default)
active, default)
english 23