Black+Decker KR60 Bedienungsanleitung Seite 4

ENGLISH
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for impact drills
Wear ear protectors with impact drills. Exposure to
x
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of
x
control can cause personal injury.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
x
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
x
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
™
4. Levelok straight drilling indicator
5. Drilling mode selector
6. Keyless chuck (KR60(L)/KR70(L))
Quick Connect ™ chuck (KR60QC/KR70QC)
7. Depth stop
8. Side handle
9. Bit storage
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
Turn the grip (10) counterclockwise until you can slide the
x
side handle (8) onto the front of the tool as shown.
Rotate the side handle into the desired position.
x
Insert the depth stop (7) into the mounting hole as shown.
x
Set the depth stop to the desired position. The maximum
x
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
x
4
Fitting a drill bit or screwdriver bit
KR60(L)/KR70(L) - Keyless chuck (fig. B)
Open the chuck by turning the front part (12) with one
x
hand while holding the rear part (11) with the other.
Insert the bit shaft (13) into the chuck and firmly tighten
x
the chuck.
KR60QC/KR70QC - Quick Connect
The chuck on these models can be easily removed and refitted.
When your project entails both drilling and screwdriving,
fit a screwdriver bit in the spindle and a drill bit in the chuck:
you will then only need to remove the chuck for screwdriving
and refit it for drilling. The screwdriver bit can be left in the
spindle while drilling. You can also fit drill bits with a
hexagonal shaft in this way.
To fit a drill bit, proceed as described above.
x
To fit a screwdriver bit, proceed as follows:
x
Remove the chuck (6).
x
Install a screwdriver bit (16) by pushing it into the spindle
x
(15) as shown.
To remove the screwdriver bit, pull the ring (17) back and
x
pull the screwdriver bit out of the spindle.
Removing and refitting the chuck
KR60(L)/KR70(L) - Keyless chuck (fig. D)
Open the chuck as far as possible.
x
Remove the chuck retaining screw, located in the front
x
part of the chuck, by turning it clockwise using a
screwdriver.
Tighten an Allen key (18) into the chuck and strike it with
x
a hammer as shown.
Remove the Allen key.
x
Remove the chuck by turning it counterclockwise.
x
To refit the chuck, screw it onto the spindle and secure it
x
with the chuck retaining screw.
KR60QC/KR70QC - Quick Connect
To remove the chuck (6), keep the release tabs (14)
x
depressed and pull the chuck off the spindle (15).
To refit the chuck, push it onto the spindle until it is firmly
x
locked into place.
Warning! Always make sure that the chuck is securely fitted.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
™
chuck (fig. B & C)
™ chuck (fig. C)