Ordering Parts; Guarantee Restrictions - Philips SENSOTOUCH 3D RQ1290 Bedienungsanleitung

Replacement
Replace the shaving unit when the shaving unit symbol appears on the display. Replace a damaged shaving unit right away.
For maximum shaving performance, we advise you to replace the shaving unit every year.
Only replace the shaving unit with an original RQ12 Philips Shaving Unit.
1 Pull the old shaving unit straight off the shaver (Fig. 23).
Note: Do not turn the shaving unit while you pull it off the shaver.
2 Insert the lug of the new shaving unit into the slot in the top of the shaver (1). Then press the shaving unit downwards (2) to attach it to
the shaver ('click') (Fig. 25).

ordering parts

The following parts are available:
- HQ8505 adapter
- RQ12 Philips Shaving Unit
- HQ110 Philips Shaving Head Cleaning Spray
- HQ200 Philips Cleaning Fluid
Environment
- Do not throw away the appliances with the normal household waste at the end of their life, but hand them in at an official collection point
for recycling. By doing this, you help to preserve the environment (Fig. 49).
- The built-in rechargeable shaver battery contains substances that may pollute the environment. Always remove the battery before you
discard or hand in the shaver at an official collection point. Dispose of the battery at an official collection point for batteries. If you have
trouble removing the battery, you can also take the appliance to a Philips service centre. The staff of this centre will remove the battery for
you and will dispose of it in an environmentally safe way (Fig. 50).
Removing the rechargeable shaver battery
Only remove the rechargeable battery when you discard the shaver. Make sure the battery is completely empty when you remove it.
Be careful, the battery strips are sharp.
1 Remove the back panel of the shaver with a screwdriver.
2 Remove the rechargeable battery.
guarantee and service
If you need service or information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips
Consumer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Consumer Care Centre
in your country, go to your local Philips dealer.

guarantee restrictions

The shaving heads (cutters and shaving guards) are not covered by the terms of the international guarantee because they are subject to wear.
troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the
information below, contact the Consumer Care Centre in your country.
Problem
The shaver does not shave as
well as it used to.
The shaver does not work
when I press the on/off
button.
Possible cause
The shaving heads are damaged or worn.
Long hairs obstruct the shaving heads.
The Jet Clean System has not cleaned the shaver
properly, because the cleaning fluid in the cleaning
chamber is soiled or the cleaning fluid level is too low.
The rechargeable battery is empty.
The travel lock is activated.
The shaving unit is soiled or damaged to such an extent
that the motor cannot run. In this case, the shaving unit
symbol, the tap symbol and the exclamation mark flash.
The temperature of the shaver is too high. In this case,
the shaver does not work and the exclamation mark on
the display flashes.
Solution
Replace the shaving unit (see chapter
'Replacement').
Clean the shaving heads by following the steps of
the extra-thorough cleaning method (see chapter
'Cleaning and maintenance').
Clean the shaver thoroughly before you continue
shaving. If necessary, clean and refill the cleaning
chamber (see chapter 'Cleaning and
maintenance').
Recharge the battery (see chapter 'Charging').
Press the on/off button for 3 seconds to
deactivate the travel lock.
Clean the shaving unit or replace it (see chapters
'Cleaning and maintenance' and 'Replacement').
Switch off the shaver and let it cool down. As
soon as the temperature of the shaver has
dropped sufficiently, you can switch on the shaver
again.
English
11