Chicco SterilNaturalDigit Gebrauchsanweisung Seite 11

DESCRIPTION:
a) �id
b) Rack
b1) Upper rack
b2) �ower rack
c) Steriliser body
c1) Heating plate
c2) Water level sensor
d) Digital display
d1) O� button (I)
d2) OFF button (0)
e) Water tank
e1) Stopper with valve
e2) Air valve
f) Power cable
g) Hygienic tongs
The Chicco Electronic Steam Steriliser allows you
to sterilise up to 4 Chicco feeding bottles, with their
accessories. It is also possible to sterilise breast pumps or
soothers if they are approved for hot sterilisation.
1) HOW TO OPERATE THE APPLIANcE
By pressing the O� button I (d1), water is automatically
sent into the heating tank, after which the heating and
disinfecting cycle begins (12 mins.). At the end of the
cycle, an acoustic signal (5 beeps) from the appliance
indicates that the cycle has finished.
If at the end of every cycle the appliance is not switched
off by pressing the 0 button (d2), it automatically repeats
a new disinfecting cycle every 5 hours (duration of
disinfection if the lid is not removed), until the water
contained in the tank has completely finished.
WARNING
If you do to wish that the appliance automatically carries
out further cycles, switch it off, pressing the OFF button
0 (d2).
2) HOW TO USE THE cHIccO STERILISER
a) A lways place the appliance out of reach of children,
on a flat, stable surfaces that is not sensitive to heat
and/or humidity, close to a mains socket that is easily
accessible (diag. 1).
b) Remove the transparent lid (diag. 2).
c) R emove the water tank from its housing. �oosen and
remove the stopper located in the lower part of the
tank� fill the tank completely with cold tap water (diag.
3). Close the water tank, tightening the stopper, and
replace it into its housing, ensuring that it is correctly
inserted into position.
NOTA IMPORTANTE: si raccomanda di non lasciare
l'acqua nella tanica per più di due giorni per evitare
l'eventuale formazione di cattivi odori e/o muffe.
d) R imuovere il cestello superiore (b1) ed inserire i
biberon smontati con il collo rivolto verso il basso
nelle apposite sedi (a seconda della tipologia dei
biberon) poste sulla base del cestello inferiore (b2). Gli
accessori possono essere posizionati in parte nelle sedi
rimanenti del cestello inferiore (b2) e le restanti sul
cestello superiore (b1) (fig. 4), riposizionare il cestello
superiore. Verificare che gli accessori posti sul cestello
superiore (b1) non impediscano la corretta chiusura
del coperchio (fig. 5).
Downloaded from www.Manualslib.com manuals search engine
WARNING! Always clean and rinse the feeding
bottles and accessories thoroughly before placing
them in the steriliser.
e) I nsert the power cable plug into the socket located at the
rear of the steriliser (diag. 6), ensuring it is fully inserted.
f) C onnect the power cable plug to the mains socket: the
digital display will light up and emit an acoustic signal
(beep), indicating that the steriliser is connected to the
mains (diag. 7).
g) P ress the On button I (d1), located at the front of the
steriliser: the appliance will emit an acoustic signal (beep)
and the display will show the symbol
the equipment is heating the water. At the same time, the
display will show the time needed, expressed in minutes,
to complete the cycle (diag. 8).
NOTE: the disinfection cycle (heating of water +
disinfection) lasts 12 minutes (approximately 7 mins.
for heating the water + 5 mins. disinfection).
WARNING
Never remove the lid of the appliance during the
disinfection cycle.
NOTE: If it is necessary to switch off the appliance
during use, press the OFF button 0 (d2) and disconnect
the power cable plug from the mains socket.
During the disinfection cycle, the hot steam coming
out from the hole located on the transparent lid
could cause serious burns. Always use the appliance
with the utmost care and attention.
When the appliance is hot, always remove the lid
slowly, with the maximum care and attention.
A) IF YOU WISH TO cARRY OUT ONLY ONE
DISINFEcTION cYcLE:
At the end of the disinfection cycle, the appliance will
emit an acoustic signal (5 beeps). At the same time, the
symbol will flash (diag. 9), and the display will show 00
until the acoustic signal stops beeping.
Switch the appliance off, by pressing the 0 button (d2)
(the display switches off)� then carry out the operations
indicated below in points h) � i) � j) � k).
B) IF YOU WISH TO cARRY OUT EXTENDED
AUTOMATIc DISINFEcTION MAINTENANcE cYcLES
EVERY 5 HOURS.
At the end of each disinfection cycle, the appliance will
emit an acoustic signal (5 beeps). At the same time,
the symbol will flash, and the display will show 00.
When the acoustic signal stops, if the appliance is not
switched off by pressing the 0 button (d2), the display
will indicate the residual time, expressed in hours, before
the appliance automatically carries out a new heating/
disinfection cycle (diag. 10).
NOTE:
The appliance will repeat the cycle every 5 hours,
until the water contained in the tank has run out.
It is possible to stop the automatic maintenance
cycles and switch off the appliance at any time,
pressing the 0 button (d2); then disconnect the
power cable plug from the mains socket.
Warning!
If the lid is removed, the disinfection maintenance
cycle is interrupted.
Warning! If, for any reason, the electricity supply
is interrupted even for a few seconds whilst the
11
indicating that