Safety Instructions - Flex WSE 7 Bedienungsanleitung

WSE 7

Safety instructions

t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=áå=
~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
 This electric power tool must be used as
a sander. Read all safety warnings,
instructions, illustrations and
specifications provided with this power
tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or
serious injury.
 Operations such as sanding, wire
brushing, or for polishing and cut-off are
not recommended to be performed with
this power tool.
Operations for which the power tool was not
designed may create a hazard and cause
personal injury.
 Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the accessory can be
attached to your power tool, it does not
assure safe operation.
 The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool.
Accessories running faster than their rated
speed can break and fly apart.
 The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly measured insertion tools cannot
be adequately shielded or controlled.
 Sanding discs, sanding pads or other
accessories must fit exactly on the
grinding spindle of your electric power
tool.
Insertion tools, which do not fit exactly on the
grinding spindle of the electric power tool,
rotate unevenly, vibrate violently and may
result in loss of control.
 Do not use a damaged accessory.
Before use, always check insertion tools
for splinters and cracks, sanding pad for
cracks, wear and severe abrasion.
If power tool or accessory is dropped,
inspect for damage or install an
undamaged accessory. After inspecting
and installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and run
the power tool at maximum no-load
speed for one minute.
Damaged accessories will normally break
apart during this test time.
 Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
If appropriate, wear a dust mask, hearing
protection, protective gloves and/or a
special apron which protect you from
small sanding and material particles.
The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator
must be capable of filtrating particles
generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.
 Keep bystanders a safe distance away
from work area. Anyone entering the work
area must wear personal protective
equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
 Hold power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire
may make exposed metal parts of the power
tool "live" and shock the operator.
 Position the cord clear of the spinning
accessory.
If you lose control, the cord may be cut or
snagged and your hand or arm may be
pulled into the spinning accessory.
15