Mounting And Dismantling Tools; Mounting And Dismantling Etx Diamond Tools; Mounting And Dismantling Diamond Milling Drums; Replacing/Adjusting The Dust Cover Ring - Schwamborn WDS 530 Originalbetriebsanleitung

EN Wall and ceiling grinding machine WDS 530 C
4 Maintenance
Increased danger of being crushed!
Wear protective gloves!
Work with the greatest care and caution!
4. Loosen (do not screw out) the 3 clamping ele­
ments [21] and fold down (! Fig. C/D/E).
The grinding machine is connected to the locat­
ing plate [8] only by the central screw [20] and
can be rotated.
For wall grinding the grinding machine must be
turned by 90°.
5. Turn the grinding machine into the desired posi­
tion (steps of 22.5°).
6. Fold the 3 clamping elements [21] up and screw
tight (! Fig. D).
7. Switch the guiding machine on.
8. Place the grinding machine with the supporting
feet [11, Fig. B] on a level, horizontal floor with
adequate load capacity (e.g. pallet or floor).
9. Switch the guiding machine off.

4.3 Mounting and dismantling tools

Risk of injury!
Wear protective gloves!
Risk of damage due to unsuitable tools!
The manufacturer strongly recommends using
only the certified tools offered by Schwamborn.
1. Place the grinding machine with the supporting
feet [11, Fig. B] on a level, horizontal floor with
adequate load capacity (e.g. pallet or floor).
2. Switch the guiding machine off.
The consistency of the surface to be ground deter­
mines the type or the composition of the tools to be
used. The manufacturer of the grinding machine can
gladly provide corresponding recommendations.

4.3.1 Mounting and dismantling ETX diamond tools

All ETX diamond tools authorised for this grind­
ing machine are dismantled and mounted in the
same manner.
26
All ETX locating plates have to be equipped with
diamond tools of the same type and the same
quantity (always 3 or 6 tools). The manufacturer
of the grinding machine can gladly provide cor­
responding recommendations.
The diamond tools need to be equal in height
(degree of wear).
1. Loosen (do not screw out) the 3 retaining
screws [37, Fig. P].
2. Turn the red retaining ring [38, Fig. P] clockwise
until the ETX diamond tools have been re­
leased.
3. Gently tap with a lump hammer to loosen the
ETX diamond tools [36, Fig. P] from the EXT
locating plate [39, Fig. P] and then remove.
4. Insert new ETX diamond tools into the re­
cess [45, Fig. S] of the ETX locating plate and
press firmly in the direction of the arrow (use
lump hammer if necessary).
5. Turn the retaining ring anti‐clockwise until the
ETX diamond tools have been clamped in.
6. Turn the 3 retaining screws [37, Fig. P] tight.

4.3.2 Mounting and dismantling diamond milling drums

Each drum mount [42, Fig Q] has to be
equipped with 3 diamond milling drums [41,
Fig Q]. The degree of wear of all diamond
milling drums should be equal.
1. If necessary, dismantle all ETX diamond tools
(! Chapter 4.3.1 – page 26).
2. Attach the 3 drum mounts to the ETX locating
plate with the supplied screws
(3 pieces each, M8).
If machining should be done with diamond
milling drums, the special dust cover ring
[46, Fig. U] needs to be mounted
(! Chapter 4.4 – page 26).

4.4 Replacing/Adjusting the dust cover ring

The dust cover ring should extend about 3 ... 8
mm beyond the grinding tools.
— Check the dust cover ring [1, Fig. A] for condi­
tion, proper position and function and, if neces­
sary, replace or adjust.
Replacing the dust cover ring
If machining should be done with diamond
milling drums, the special dust cover ring [46,
Fig. U] needs to be mounted
(! Chapter 4.4 – page 26).