Remote Sensor 2; Display 3; Front Usb Input 6; Aptx Bluetooth Connection 0 - Rotel RC1590SIL Bedienungsanleitung

English
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.

Remote Sensor 2

This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.

Display 3

The front panel display shows the source selected, volume level and tone
settings. The display can be dimmed using the RC-1590 setup menu or the IR
remote controller. See the Dimmer Control section of this manual for details.

Front USB Input 6

See Figure 6
The front USB input can be connected to an iPod or iPhone. With iPod or
iPhones, simply plug the device into the front USB and select USB function
from the source selector. The iPod and iPhone remain active allowing search
and play functions.

APTX Bluetooth Connection 0

The Bluetooth Antenna 0 on the RC-1590's back panel is for wireless
streaming via Bluetooth, from your device (i.e. mobile phones). From your
mobile device, look for "Rotel Bluetooth" and connect to it. Connection is
normally automatic, but if prompted for a password, please press "0000"
on your device. The RC-1590's supports both traditional Bluetooth and APTX
Bluetooth audio streaming.

Audio Controls

Volume Control 4 DE

Turn the knob clockwise to increase the volume, or counter clockwise to
decrease the volume. From the remote control press the volume + or -
button to turn the volume up or down. Press the MUTE
mute the volume.

Balance Control 9 C

The Balance Control adjusts the left-to-right balance of the sound output. The
factory default is the center position or "0". To change the balance from
the front panel, press the MENU
BALANCE SETTING mode. Then press the - or + buttons on the front panel to
change the value to LEFT or RIGHT. The value can change from L15 to R15.
NOTE: This setting is saved permanently including after powering off
the RC-1590.
To make temporary changes not saved after power off, from the remote
C
control press the BAL button to access the BALANCE setting, then press
G
the left/right arrow buttons to adjust. When finished, press the ENTER
G
button to exit the menu.
E
button to completely
9
button to toggle the front display to

Tone Control Bypass 9 C

Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show TONE
BYPASS. To turn on the tone control from the front panel, press the MENU
9
button to toggle to the Bypass control then press the - or + buttons on
the front panel to turn bypass on or off.
NOTE: This setting is saved permanently including after powering off
the RC-1590.
To temporarily change the Tone Control Bypass, press the TONE
on the front panel, then press the - or + button on the front panel to turn
the Bypass on or off, or press the BYPASS

Bass and Treble Controls 9 C

Set the Bass or Treble controls from the front panel by pressing the MENU
9
button to toggle to either the Bass or Treble Setting menu. Then press
the - or + button on the front panel to adjust the value. The Bass and Treble
values range from -10 to +10.
NOTE: These settings are saved permanently including after powering
off the RC-1590.
To temporarily change the Bass and Treble settings, press the TONE
button on the front panel to toggle to the Bass or Treble Setting, then press
the - or + button on the front panel to adjust the value. Or from the remote
control, press the BASS or TREBLE
arrow buttons on the remote control.
NOTE: When Tone Bybass is disabled, Bass and Treble settings can
not be changed by the Tone button
A properly setup high-performance audio system produces the most natural
sound with little or no adjustment of the tone controls. Use these controls
sparingly. Be particularly careful when turning the controls up as this
increases the power output in the bass or treble range, increasing the load
on the amplifier and speakers.
NOTE: Setting the Bass and Treble controls do not automatically turn
on the tone control. To turn on tone control, refer to previous section
Tone Control Bypass.
NOTE: Tone Bypass, Bass, Treble and Balance settings are only saved
D
permanently from within the Menu. Adjustments made using the
buttons are temporary only and not saved after power off.

Function Control 8 L

The Function control selects the input signal source. From the front panel
or remote control press the corresponding input button to select the source
to listen to.

Dimmer Control

Display Dimmer 9 B

To change the brightness of the front display, press the MENU
to toggle to the Display Settings. Then press the - or + buttons on the front
panel to change the display brightness.
NOTE: This setting is saved permanently including after powering off
the RC-1590.
7
C
button on the remote control.
C
button, then press the left/right
or the BASS/TREBLE buttons
7
9
13
button
7
G
.
C
7 C
button