Kettler TRACK SC Montageanleitung Seite 6

Assembly Instructions
GB
Running Tip: Running straight on the treadmill is made
easier by focussin on a fixed oject in front of you in the room.
Rus as if you wanted to approach the object.
Care and Maintenance
Do no use corrosive or abrasive materials to clean the
equipment. Ensure that such materials are not allowed
to pollute the environment.
The electrical elements and components do not require
special maintenance. No alterations or repairs (except
maintenance checks) should be made to these parts
unless by a qualified electrician.
When ordering spare parts, always state the full article
Instructions for Assembly
Ensure that you have received all the parts required (see
check list) and that they are undamaged. Should you
have any cause for complaint, please contact your
KETTLER dealer.
Before assembling the equipment, study the drawings
carefully and carry out the operations in the order shown
by the diagrams. The correct sequence is given in
capital letters.
The equipment must be assembled with due care by an
adult person. If in doubt call upon the help of a second
person, if possible technically talented.
Please note that there is always a danger of injury when
working with tools or doing manual work. Therefore
please be careful when assembling this machine.
Ensure that your working area is free of possible sources of
Handling
Belt adjustment:
The running belt has been adjusted properly at the factory.
However transportation, uneven flooring or other
unpredicted reasons could cause the belt to shift off center.
First unplug the power cord from the surge protector.
If the belt moves to the left:
Using the hex key provided, turn the left rear roller
adjustment bolt 1/4 turn in the clockwise direction. Plug the
power cord back into the surge protector and run the
treadmill at 4 km/h. You should see the belt start to correct
itself, moving back toward the center. Repeat the above
procedure until the walking belt is centered.
KETTLER Ltd. • KETTLER House, Merse Road • North Moons Moat • Redditch, Worchestershire • B 98 9 HL • Great Britan
KETTLER International Inc. – 1355, London Bridge Road – VA 23450 Virginia Beach (USA)
Importantly: Please keep the safety key in a safe place
and ensure that it is kept out of reach of children!
number, spare-part number, the quantity required and the
serial number of the product.
Example order: item no. 07885-500 / spare-part no.
68001000 / 1 pieces /serial no......
Important: spare part prices do not include fastening
material; if fastening material (bolts, nuts, washers etc.) is
required, this should be clearly stated on the order by
adding the words „with fastening material".
danger, for example don't leave any tools lying around.
Always dispose packaging material in such a way that it
may not cause any danger. There is always a risk of
suffocation if children play with plastic bags!
The fastening material required for each assembly
step is shown in the diagram inset. Use the fastening
material exactly as instructed. The required tools are
supplied with the equipment.
Bolt all the parts together loosely at first, and check
that they have been assembled correctly. Then use
spanner to finally tighten screws/nuts.
Please keep original packaging of this article, so that
it may be used for transport at a later date, if
necessary.
For technical reasons, we reserve the right to carry out
preliminary assembly work (e.g. addition of tubing plugs).
If the belt moves to the right:
Using the hex key provided, turn the right rear roller
adjustment bolt 1/4 turn in the clockwise direction. Plug the
power cord back into the surge protector and run the
treadmill at 4 km/h. You should see the belt start to correct
itself, moving back toward the center. Repeat the above
procedure until the walking belt is centered. It may be
necessary to set walking belt tension once you have
completed this procedure if the belt feels like it is slipping
while walking. Refer below to the "Belt straightening"
instructions.
Belt straightening:
First unplug the power cord from the surge protector. Using
the hex key provided, turn both the left and right rear roller
adjustment bolts the same distance, usually a 1/4 turn in the
clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 4 km/h. You should now
walk on the belt to determine if the belt is still slipping.
Repeat the above procedure until the walking belt is not
slipping. Be very careful when adjusting and
straightening the belt. An extreme over or under
tension may damage the running belt! The tension
should be just tight enough not to slip.
6
www.kettler.de