Technical Data; Inserting/Changing The Batteries; Starting Operation - Bosch GLL 2-10 Professional Originalbetriebsanleitung

A)
(20) Laser target plate
(21) Protective bag
A)
(22) Laser goggles
A)
(23) Tripod (BT 150)
(24) Telescopic shaft (BT 350)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Line laser
Article number
A)
Working range at least
Levelling accuracy
Typical self-levelling range
Typical levelling time
Operating temperature
Storage temperature
Max. altitude
Relative air humidity max.
Pollution degree according to
IEC 61010-1
Laser class
Laser type
C
6
Divergence
Tripod mount
Batteries
Operating duration in operating mode
– Cross-line mode
– Line mode
Weight according to
EPTA-Procedure 01:2014
Dimensions (length × width ×
height)
Protection rating
A) The working range may be reduced by unfavourable environ-
mental conditions (e.g. direct sunlight).
B) Only non-conductive deposits occur, whereby occasional tem-
porary conductivity caused by condensation is expected.
The serial number (10) on the type plate is used to clearly identify
your measuring tool.
Assembly

Inserting/changing the batteries

It is recommended that you use alkaline manganese batter-
ies to operate the measuring tool.
Bosch Power Tools
To open the battery compartment cover (11), press on the
locking mechanism (12) and remove the battery compart-
ment cover. Insert the batteries.
When inserting the batteries, ensure that the polarity is cor-
rect according to the illustration on the inside of the battery
A)
compartment.
If the batteries become weak, the status indicator (8) will
flash. The measuring tool can still be operated for approxim-
ately 1 hour after the first flash.
Always replace all the batteries at the same time. Only use
batteries from the same manufacturer and which have the
same capacity.
GLL 2-10
u
3 601 K63 L..
10 m
±0.3 mm/m
±4°
Working with the RM 1 rotating mount
< 4 s
(see figures A – B)
−10 °C to +50 °C
You can use the rotating mount (13) to rotate the measuring
−20 °C to +70 °C
tool 360° around a central, always visible plumb point. This
enables you to set up the laser lines without having to
2000 m
change the position of the measuring tool.
90 %
Place the measuring tool with the guide groove (17) on the
B)
2
guide rail (14) of the rotating mount (13) and slide the
measuring tool all the way onto the platform.
2
To disconnect the measuring tool, pull it off the rotating
mount in the opposite direction.
630–650 nm, < 1 mW
Rotating mount positioning options:
1
– Standing on a flat surface,
0.5 mrad (full angle)
– Screwed to a vertical surface,
1/4"; 5/8"
– On metal ceiling strips using the ceiling clip (18),
3 × 1.5 V LR6 (AA)
– On metallic surfaces using the magnets (15).
9 h
Operation
17 h

Starting Operation

0.49 kg
u
112 × 55 × 106 mm
u
IP 54 (dust- and splash-
proof)
u
Take the batteries out of the measuring tool when you
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
storage in the measuring tool.
Protect the measuring tool from moisture and direct
sunlight.
Do not expose the measuring tool to any extreme tem-
peratures or fluctuations in temperature. For example,
do not leave it in a car for extended periods of time. If it
has been subjected to significant fluctuations in temper-
ature, first allow the measuring tool to adjust to the ambi-
ent temperature and then always carry out an accuracy
check before continuing work (see "Accuracy Check of
the Measuring Tool", page 14).
The precision of the measuring tool may be compromised
if exposed to extreme temperatures or fluctuations in
temperature.
Avoid substantial knocks to the measuring tool and
avoid dropping it. Always carry out an accuracy check
before continuing work if the measuring tool has been
subjected to severe external influences (see "Accuracy
Check of the Measuring Tool", page 14).
1 609 92A 4HJ | (20.03.2020)
English | 13