Princess 242120 Handbuch Seite 20

• If required, insert the paper filter (19) in the
ground coffee cassette (10).
• Put the ground coffee in the ground coffee
cassette (10).
- If you want regular coffee, put ground
coffee in the ground coffee cassette.
- If you want espresso, put espresso
powder in the ground coffee cassette.
• Place the lid (20) on the ground coffee
cassette (10).
• Put the ground coffee cassette (10) in the
side marked '2' on the coffee pad cassette
(9).
• Insert the coffee pad cassette (9) into the
appliance with the ground coffee cassette
upwards.
• Place the required amount of cups under
the coffee dispenser (5).
- For one cup, place the cup under both
dispenser nozzles of the coffee
dispenser (fig. J1).
- For two cups, place one cup under the
left dispenser nozzle and one cup under
the right dispenser nozzle of the coffee
dispenser (fig. J2).
• Press the on/off button (1) to switch on the
appliance. The start/stop button (2)
becomes red. The start/stop button (2)
becomes green when the appliance is
ready for use.
• Set the dispenser selector (4) to position 'D'.
• Set the cup size selector (3) to the required
position.
• Press the start/stop button (2).
• To interrupt the process, press the start/
stop button (2) again.
• If the process is completed, set the
dispenser selector (4) to position 'A'.
Hot water dispenser (fig. A, B & C)
The hot water dispenser can be used for
preparing tea or instant beverages.
Warning! Be careful with hot water and steam
to avoid burns.
• Set the dispenser selector (4) to position 'A'.
• Place the cup on the cup tray (11) directly
under the hot water dispenser (7).
• Press the on/off button (1) to switch on the
appliance. The start/stop button (2)
becomes red.
The start/stop button (2) becomes green
when the appliance is ready for use.
• Set the dispenser selector (4) to position 'B'.
• Set the cup size selector (3) to the required
position.
• Press the start/stop button (2).
• To interrupt the process, press the start/
stop button (2) again.
• If the process is completed, set the
dispenser selector (4) to position 'A'.
Milk frothing unit (fig. A, B, C & K)
The milk frothing unit combines milk, steam
and air dispensing a cascade of frothy milk
directly into the cup.
Warning!
• Be careful with hot steam to avoid burns.
• Only remove the milk jug and the cup when
the when the milk frothing process is
completed. The milk frothing process does
not stop immediately.
Caution! Only use the milk frothing unit under
the following conditions:
- The milk frothing unit must be properly
assembled.
- The milk frothing unit must be properly
mounted to the appliance.
- A cup must be placed directly under the
milk froth dispenser.
- A suitable milk jug filled with a sufficient
amount of cold milk must be placed as
close to the lef side of the appliance as
possible. The flexible tube must reach the
bottom of the milk jug.
• Set the dispenser selector (4) to position 'A'.
• Fill the milk jug with a sufficient amount of
cold milk.
• Place the milk jug as close to the left side
of the appliance as possible. Make sure
that the flexible tube (21) reaches the
bottom of the milk jug.
• Place the cup on the cup tray (11) directly
under the milk froth dispenser (8).
• Press the on/off button (1) to switch on the
appliance. The start/stop button (2) flashes
red. The start/stop button (2) becomes
green when the appliance is ready for use.
• Set the dispenser selector (4) to position
'C'. The on/off button (1) becomes blue.
20