Pulsar DIGISIGHT ULTRA N450 LRF Bedienungsanleitung Seite 12

Wi-Fi access level
This submenu allows you to set required access level of the Stream Vision application to
setup your riflescope.
Access level Owner. The Stream Vision user has the complete access to all riflescope's
functions.
Access level Guest. The Stream Vision user has the access only to the real time video
stream from the riflescope.
•
Press and hold down the MENU button (6) to enter the main menu, select the "Wi-Fi
Settings" menu item, then the "Wi-Fi access level setup" submenu.
•
Use the UP (7) and DOWN (5) buttons to select the access level.
•
To confirm the selection, press the MENU button (6).
•
To exit the submenu, press and hold the MENU button (6).
DEVICE •
Press and hold the MENU button (6) to enter the main menu.
INFORMATION
•
Select the "Device information" submenu and briefly press the MENU button (6) to enter.
This item allows the user to view the following information about the riflescope:
- full name of the riflescope,
- SKU number,
- Serial number,
- software version,
- hardware version,
- service information.
VIDEO RECORDING AND PHOTOGRAPHY
The Digisight Ultra LRF riflescopes feature video recording (photography) of the image being observed to the
internal memory card.
Before using the functions of video recording and photography, please read the "Date setup", "Time setup" menu
items of the "Main menu functions" section.
The built-in recorder operates in two modes:
Photo (photography; in the top left corner of the display you can see a photography icon
of photos that can be saved to the Flash card is more than 100, message ">100" is shown.
Video (video recording; in the top left corner of the display you can see an icon
format HH:MM:SS (hours : minutes : seconds)
When switched on, the riflescope is in the Video mode. Toggle between Video and Photo modes with a long press of
the REC (4) button. Switching is cyclical (Video-> Photo-> Video...).
PHOTO MODE. PHOTOGRAPHY.
•
Switch to the Photo mode with a long press of the REC button (4).
•
Press the REC button (4) briefly to take a picture. The image freezes for 0.5 sec - a photo is saved to the
internal memory.
VIDEO MODE. VIDEO RECORDING.
•
Switch to the Video mode with a long press of the REC (4) button.
•
Press the REC button (4) briefly to start video recording.
•
Upon start of video recording icon
(minutes : seconds) appear instead.
•
To pause video recording and then start (continue video recording), press the REC button (4) briefly.
•
To stop video recording, press and hold the REC button (4).
USER MANUAL FOR DIGISIGHT ULTRA LRF NIGHT VISION DIGITAL RIFLESCOPE
). If estimated number
, total video time left in the
disappears, icon Rec and recording timer in the format MM:SS
•
Video files are saved to the built-in memory card:
•
After stopping video recording
•
Upon powering the riflescope off if recording was on;
•
When the memory card is overfilled during record ("Memory full" message appears on the display).
Notes:
You can enter and navigate the menu during video recording.
Recorded videos and photos are saved to the built-in memory card of the riflescope in the format img_xxx.jpg (for
photos); video_xxx. mp4 (for video). xxx - three-digit counter (for videos and photos).
The counter for multimedia files cannot be reset.
If a file is deleted from the middle of the list, its number is not taken by another file.
When the counter is full, a new folder is created - img_xxxx, where xxxx is the folder counter.
The maximum duration of a recorded file is five minutes. After this time expires a video is recorded into a new file.
The number of recorded files is limited by the capacity of unit's internal memory.
Check regularly the free capacity of the internal memory, move recorded footage to other storage media to free up
space on the internal memory card.
Graphic data (status bar, icons and other) are not shown in recorded video/ photo files.
Important information!
To play recorded video files on computers running iOS, we recommend using the following players: VLC video player
(http://www.videolan.org/vlc/download-macosx.html) or Elmedia player (itunes.apple.com/us/app/elmedia-
multiformat-video/id937759555?mt=12).
DISPLAY OFF FUNCTION
This function deactivates transmission of image to the display by minimizing its
brightness. This helps prevent accidental disclosure. The riflescope and the built-in IR
illuminator keep running.
•
When the riflescope is on, press and hold down the ON/OFF button (18) for 1-2 seconds. The display goes out,
the "Display off" message appears.
•
To turn on the display, press the ON / OFF button (18) briefly.
•
If the ON/OFF button (18) is held down for more than 3 seconds, the display shows the "Display off" message
with countdown, the device will turn off.
PIP FUNCTION
The PiP function (Picture in Picture) allows you to see a zoomed image simultaneously with the main image in a
dedicated window.
•
To turn on/off the PiP function, press and hold the DOWN button (5).
•
To change zoom ratio in the PiP window, press the DOWN button (5) briefly.
•
Required digital zoom can also be set in the quick menu.
•
The zoomed image is displayed in a dedicated window, with the
full magnification being used.
•
The rest of the image is displayed only with the optical
magnification (digital magnification is off).
•
When PiP is turned off, the display shows the full magnification
set for the PiP mode.
12