Maintenance - Black & Decker KR750 Übersetzung Der Originalanleitung

ENGLISH
Setting the drilling depth (fi g. E)
♦ Slacken the side handle (7) by turning the grip
counter clockwise.
♦ Set the depth stop (6) to the desired position.
The maximum drilling depth is equal to the
distance between the tip of the drill bit and the
front end of the depth stop.
♦ Tighten the side handle by turning the grip
clockwise.
Switching on and off
♦ To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far
you press the switch. As a general rule, use
low speeds for large diameter drill bits and
high speeds for smaller diameter drill bits.
♦ For continuous operation, press the lock-on
button (2) and release the variable speed
switch. This option is available only at full
speed in both forward and reverse modes.
♦ To switch the tool off, release the variable
speed switch. To switch the tool off when
in continuous operation, press the variable
speed switch again and release it.
Accessories
The performance of your tool depends on the
accessory used. BLACK+DECKER and Piranha
accessories are engineered to high quality stand-
ards and designed to enhance the performance of
your tool. By using these accessories you will get
the very best from your tool.

Maintenance

Your BLACK+DECKER tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Warning! Before performing any maintenance,
switch off and unplug the tool.
♦ Regularly clean the ventilation slots in your
tool using a soft brush or dry cloth.
♦ Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner.
♦ Regularly open the chuck and tap it to remove
any dust from the interior (when fi tted).
Protecting the environment
Separate collection. This product must
not be disposed of with normal household
waste.
34
Products and batteries contain materials that can
be recovered or recycled, reducing demand for
raw materials. Please recycle electrical products
and batteries according to local provisions.
Further information is available at
www.2helpU.com.
Technical data
Input voltage
Power input
No-load speed
Max drilling capacity
Steel/concrete
Wood
Weight
Level of sound pressure according to EN 60745:
Sound pressure (L ) 101 dB(A), uncertainty (K) 3 dB(A),
pA
Sound power (L ) 112 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 60745:
Impact drilling into concrete (a
1.5 m/s², Drilling into metal (a
EC declaration of conformity
MACHINERY DIRECTIVE
KR750 - Drill
Black & Decker declares that these products
described under "technical data" are in
compliance with: 2006/42/EC, EN 60745-1:2009
+A1:2010 EN 60745-2-1:2010.
These products also comply with Directive
2004/108/EC (until 19/04/2016) 2014/30/EU (from
20/04/2016) and 2011/65/EU.
For more information, please contact
Black & Decker at the following address or refer to
the back of the manual.
The undersigned is responsible for compilation of
the technical fi le and makes this declaration on
behalf of Black & Decker.
KR750 (Type 3)
V 230
AC
W 710
Min 0 - 2800
-1
mm 13
mm 25
kg 2.0
) = 17.97 m/s², uncertainty (K)
h, ID
) = 3.37 m/s², uncertainty (K) 1.5 m/s²
h, D
R. Laverick
Engineering Director
Black & Decker Europe
210 Bath Road, Slough
Berkshire, SL1 3YD
United Kingdom
19/11/2015