Important Remarks; Important Safety Instructions; Installation Instructions - Cardin Elettronica BL-Serie Bedienungsanleitung

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLA-
TION. PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
NOT READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORK-
ING ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
• These instructions are aimed at professionally qualified "installers of electrical
equipment" and must respect the local standards and regulations in force.
All materials used must be approved and must suit the environment in which
the installation is situated.
• All maintenance operations must be carried out by professionally qualified
technicians. Before carrying out any cleaning or maintenance operations
make sure the power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it has been
made. "i.e. for the automation of hinged gates" with one or two gate leaves.
• The unit may be fitted both to the right and to the left of the passageway. This
product and all its relative components has been designed and manufactured
by Cardin Elettronica who have verified that the product conforms in every
aspect to the safety standards in force.
Any non authorised modifications are to be considered improper dangerous
and the complete responsibility of the installer.
Caution! mechanical stop buffers must be installed in both the open-
ing and closing positions (pos. 1, 2, 3, fig. 10).

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the following public safety
conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from the main
road to eliminate possible traffic disruptions.
2) The operator must be installed on the inside of the property and not on the
public side of the gate. The gates must not swing outwards onto a public area.
3) The gate operator is designed for use on gates through which vehicles are
passing. Pedestrians should use a separate entrance.
4) The gate must be in full view when it is operating therefore controls must be
situated in a position where the operator can see the gate at all times.
5) At least two warning signs (similar to the example on the right) should be
placed, where they can be easily seen by the public, in the area of the system
of automatic operation. One inside the property and one on the public side of
the installation. These signs must be indelible and not hidden by any objects
(such as tree branches, decorative fencing etc.).
6) Make sure that the end-user is aware that children and/or
pets must not be allowed to play within the area of a gate
installation. If possible include this in the warning signs.
7) Whenever a fully open gate leaf comes within at least 500
mm of a fixed structure the space must be protected by
an anticrush buffer.
8) A correct earth connection is fundamental in order to guar-
antee the electrical safety of the machine
9) If you have any questions about the safety of the gate
operating system, do not install the operator. Contact your
dealer for assistance.
TECHNICAL DESCRIPTION
200/BL2124 Self-locking electromechanical 24 Vdc operator suitable for
hinged gates up to 2 m in length and 150 kg in weight (per gate leaf).
200/BL2124L Self-locking electromechanical 24 Vdc operator suitable for
hinged gates up to 2 m in length and 150 kg in weight (per gate leaf).
If used with the maximum travel distance an opening angle of 90° and the
addition of an electric locking device, it can be used for gates up to 4 m in
length and 150 kg in weight.
200/BL2124C Self-locking electromechanical 24 Vdc operator suitable for
hinged gates up to 1,8 m in length and 150 kg in weight (per gate leaf).
If used with the maximum travel distance an opening angle of 90° and the
addition of an electric locking device, it can be used for gates up to 3 m in
length and 150 kg in weight.
- 24 Vdc motor with a steel never ending screw.
- External carter in extruded aluminium.
- Release mechanism components in shockproof plastic.
- Geared motor with steel gears enclosed in a die cast 2-piece aluminium
shell.
- Brackets and accessories in zinc-plated steel.
- Lubrication using permanently fluid grease.
ACCESSORIES
206/BL201STAP
- Adjustable rear bracket for fitting to a wall
206/BL201SUAR - Adjustable rear plate for fitting to a gate
980/XLSE11C - Electric locking device 12 Vac
IMPORTANT REMARKS
USER INSTRUCTIONS
Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials. Illicitly disposing of this
product by the owner is punishable by law and will be dealt with according
to the laws and standards of the individual member nation.
During the opening/closing manoeuvre check for correct operation and activate
the emergency stop button in case of danger.
During blackouts the gate can be released and manually manoeuvred using
the supplied release key (see manual release pag. 13).
Periodically check the moving parts for wear and tear and grease if required,
paying particular attention to the never ending screw pos. 11 fig. 3 (200/
BL2124C), using lubricants which maintain their friction levels unaltered
throughout time and are suitable for temperatures of -20 to +70°C.
In case of failure or operational anomalies switch off the power at the mains
do not attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices (photoelectric
cells etc.).
Eventual repair work must be carried out by specialised personnel using
original spare parts.
The appliance is not suitable for continuous operation and must be adjusted
according to the model (see technical data on page 24).

INSTALLATION INSTRUCTIONS

The minimum controls which may be installed are OPEN-STOP-CLOSE, these
controls must be installed in a location not accessible to children.
WARNING
Before starting the installation of the system check that the structure which
AUTOMATIC OPENING
KEEP CLEAR
is to be automated is in good working order and respects the local standards
and regulations in force.
To this end make sure that the gate is sufficiently rigid (if necessary reinforce
the structure) and that the runner guides slide easily.
You are advised to grease all the moving parts using lubricants which maintain
CHILDREN OR PETS MUST NOT
unaltered friction characteristics over a period of time and are suitable for
BE ALLOWED TO PLAY ON OR
NEAR THE INSTALLATION
temperatures of -20 to +70°C.
• Check the safety measures between the fixed and moving parts:
- a minimum space of 30 mm must always be left along the entire distance
between the gate and the support column measured throughout the entire
opening angle of the gate;
- make sure that the space between the bottom of the gate and the
pavement never exceeds 30 mm throughout the entire opening angle of
the gate.
• The surface of the gate must not feature openings which allow a person's
hand or foot to pass through.
• Check the exact positioning of the pivots, and their good working order
(the upper and lower hinges/pivots must be aligned on the same axis).
• Work out the run of the cables according to the command and control devices
fitted and make sure the system conforms to the local standard and regula-
tions in force (see installation example fig. 1 pag. 2).
• Check that the appliance is suitable for the size, weight and duty cycle of
the gate to which it is to be applied (see duty cycle on page 24)
FITTING THE UNITS 200/BL2124 - BL2124L
The unit may be positioned either to the right or to the left of the passage-
way. To install the unit correctly carry out the following procedure carefully.
• Move the gate/s to the closed position.
• Select the type of opening required (fig. 7,8 pag. 5).
• Fasten the rear mooring bracket to the column (fig. 12 pag. 7), taking
into account the measurements "A" and "B", after having checked the
position of the gate hinge with respect to the column (measurement "C"
fig. 7,8 page 5) according to the type of opening required.
12
IMPORTANT REMARKS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user
is therefore obliged to either take the product to a suitable dif-
ferential collection site for electronic and electrical goods or to
send it back to the manufacturer if the intention is to replace it
with a new equivalent version of the same product.