Important Remarks; Important Safety Instructions; Installation Instructions - Cardin Elettronica BL Serie Anleitung

IMPORTANT REMARkS

TO REDUCE THE RISk OF SEVERE INJURY OR DEATH READ THE FOLLOWING REMARkS
CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION. PAY PARTICULAR ATTENTION
TO ALL THE PARAGRAPHS MARkED WITH THE SYMBOL
INSTRUCTIONS COULD COMPROMISE THE CORRECT WORkING ORDER OF THE SYSTEM.
• These instructions are aimed at professionally qualified "INSTALL-
ERS OF ELECTRICAL EQUIPMENT" and must respect the local
standards and regulations in force. All materials used must be
approved and must suit the environment in which the installation
is situated.
• All maintenance operations must be carried out by professionally
qualified technicians. Before carrying out any cleaning or main-
tenance operations make sure the power is disconnected at the
mains.
• This appliance must be used exclusively for the purpose for which
it has been made. "i.e. for the automation of one or two hinged
gates".
The appliance may be used to operate hinged gates, with one
or two gate leaves.
• The unit may be fitted both to the right and to the left of the pas-
sageway.
• This product and all its relative components has been designed
and manufactured by Cardin Elettronica who have verified that
the product conforms in every aspect to the safety standards in
force.
Any non authorised modifications are to be considered improper
and therefore dangerous.
The manufacturer accepts no liability for situations arising from
the use of an electrical installation which does not conform to the
local standards and regulations in force and in particular when
the earthing circuit is not efficient.

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the following
public safety conditions are satisfied:
1) Ensure that the gate operating installation is far enough away
from the main road to eliminate possible traffic disruptions.
2) The operator must be installed on the inside of the property and
not on the public side of the gate. The gates must not swing
outwards onto a public area.
3) The gate operator is designed for use on gates through which vehi-
cles are passing. Pedestrians should use a separate entrance.
4) The gate must be in full view when it is operating therefore controls
must be situated in a position where the operator can see the
gate at all times.
5) At least two warning signs (similar to the example on the right)
should be placed, where they can be easily seen by the public,
in the area of the system of automatic operation. One inside the
property and one on the public side of the installation.
These signs must be indelible and not hidden by any objects (such
as tree branches, decorative fencing etc.).
6) Make sure that the end-user is aware that children and/or pets
must not be allowed to play within the area of a gate installation.
If possible include this in the warning signs.
7) Whenever a fully open gate leaf comes within at least 500 mm of
a fixed structure the space must be protected by an anticrush
buffer.
8) A correct earth connection is fundamental in
order to guarantee the electrical safety of the
machine
9) If you have any questions about the safety of
the gate operating system, do not install the
operator. Contact your dealer for assistance.
IMPORTANT REMARkS
TECHNICAL DESCRIPTION
200/BL203 Self-locking electromechanical operator suitable for
hinged gates up to 2,0 metres in length and 150 kg in weight
(per gate leaf).
200/BL203L Self-locking electromechanical operator suitable for
hinged gates up to 2 metres in length and 150 kg in weight (per
gate leaf).
If used with the maximum travel distance an opening angle of 90°
and the addition of an electric locking device, it can be used for
gates up to 4 metres in length and 150 kg in weight.
200/BL203C - 200/BL203CE Self-locking electromechanical
operator suitable for hinged gates up to 1,8 metres in length and
150 kg in weight (per gate leaf).
If used with the maximum travel distance an opening angle of 90°
and the addition of an electric locking device, it can be used for
gates up to 3 metres in length and 150 kg in weight.
200/BL352 Reversible electromechanical operator suitable for
hinged gates up to 3,5 m in length and 300 kg in weight (per
gate leaf).
200/BL452 Reversible electromechanical operator suitable for
hinged gates up to 4,5 m in length and 300 kg in weight (per
gate leaf).
- Single phase motor housed in a cast aluminium case with incor-
porated overload protector .
- External carter in extruded aluminium.
- Release mechanism components in shockproof plastic.
- Geared motor with steel gears enclosed in a die cast two-piece
aluminium shell (BL203-202L-202C).
- Silent running epicycloid reduction motor with a never ending
universal ball screw in steel (BL352-452).
- Brackets and accessories in zinc-plated steel.
- Lubrication using permanently fluid grease.
ACCESSORIES
206/BL201STAP - Adjustable rear bracket for fitting to a wall
206/BL201SUAR - Adjustable rear plate for fitting to a gate
980/xLSE11C

INSTALLATION INSTRUCTIONS

The minimum controls which may be installed are OPEN-
STOP-CLOSE, these controls must be installed in a location
not accessible to children. Before starting the installation of
the system check that the structure which is to be automated
is in good working order and respects the local standards and
regulations in force.
To this end make sure that the gate is sufficiently rigid (if nec-
essary reinforce the structure) and that the runner guides slide
easily. You are advised to grease all the moving parts using lubri-
cants which maintain unaltered friction characteristics over a
period of time and are suitable for temperatures of -20 to +70°C.
• Check the safety measures between the fixed and moving
parts:
- a minimum space of 30 mm must always be left along the entire
distance between the gate and the support column measured
throughout the entire opening angle of the gate.
- make sure that the space between the bottom of the gate
WARNING
and the pavement never exceeds 30 mm throughout the entire
AUTOMATIC OPENING
kEEP CLEAR
opening angle of the gate.
• The surface of the gate must not feature openings which allow
a person's hand or foot to pass through.
• Check the exact positioning of the pivots, and their good work-
ing order (the upper and lower hinges/pivots must be aligned
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
on the same axis).
NEAR THE INSTALLATION
15
IMPORTANT REMARkS
. NOT READING THESE IMPORTANT
- Electric locking device 12 Vac