Rules For Safe Operation - Ryobi EDP-5530L Bedienungsanleitung

GB
F D
THANK YOU FOR BUYING A RYOBI 305 MM DRILL
PRESS.
Your new drill press has been engineered and
manufactured to Ryobi's high standard for dependability,
ease of operation and operator's safety. Properly
cared for, it wil give you years of rugged trouble free
performance.
CAUTION
Carefully read through this entire owner's
manual before using your DRILL PRESS.
Pay close attention to the Rules for Safe Operation,
Warnings and Cautions.
If you use your tool properly and only for what it is
intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE.

RULES FOR SAFE OPERATION

WARNING
Read and understand all instructions. Failure
to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
READ ALL INSTRUCTIONS.
KNOW YOUR POWER TOOL. Read the operator's
■
manual carefully. Learn the applications and
limitations as well as the specific potential hazards
related to this tool.
GUARD AGAINST ELECTRICAL SHOCK BY
■
PREVENTING BODY CONTACT WITH GROUNDED
SURFACES. For example: pipes, radiators, ranges,
refrigerator enclosures.
KEEP GUARDS IN PLACE and in good working
■
order.
REMOVE ADJUSTING KEYS AND WRENCHES.
■
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and
■
benches invite accidents. DO NOT leave tools or
pieces of wood on the tool while it is in operation.
DO NOT USE IN DANGEROUS ENVIRONMENTS.
■
Do not use power tools in damp or wet locations or
expose to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visitors
■
should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
E I P NL S DK N FIN
English
MAKE WORKSHOP CHILDPROOF with padlocks,
■
master switches, or by removing starter keys.
DON'T FORCE THE TOOL. It will do the job better
■
and safer at the feed rate for which it was designed.
USE THE RIGHT TOOL. Do not force the tool or
■
attachment to do a job for which it was not designed.
USE THE PROPER EXTENSION CORD. Make sure
■
your extension cord is in good condition. Use only a
cord heavy enough to carry the current your product
will draw. ,An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
A wire gauge size (A.W.G.) of at least 16 is
recommended for an extension cord 50 feet or less in
length. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
DRESS PROPERLY. Do not wear loose clothing,
■
gloves, neckties, or jewelry that can get caught and
draw you into moving parts. Rubber gloves and
nonskid footwear are recommended when working
outdoors. Also wear protective hair covering to
contain long hair.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
■
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
SECURE WORK. Use clamps or a vise to hold work
■
when practical, it is safer than using your hand and
frees both hands to operate the tool.
DO NOT OVERREACH. Keep proper footing and
■
balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
■
and clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before
■
servicing, or when changing attachments, blades,
bits, cutters, etc., all tools should be disconnected
from power source.
AVOID ACCIDENTAL STARTING. Be sure switch is
■
off when plugging in any tool.
USE RECOMMENDED ACCESSORIES. Consult the
■
operator's manual for recommended accessories.
The use of improper accessories may result in injury.
NEVER STAND ON TOOL. Serious injury could
■
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
CHECK DAMAGED PARTS. Before further use of
■
the tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation.
14
GR H CZ RUS RO PL