External Power Supply; Operation; Battery Installation - Pulsar Apex LRF XQ serie Handbuch

SIGHT STATUS FIRST SHORT
(CURRENT PRESS
OPERATING
MODE)
Button
Sight is off Power sight on
ON
Display off Turn display on
Sight is on
Turn display off
Button
Calibrate the sensor
Display on
CAL
Color inversion
Activation of
Button
Sight is on
rangefinder
LRF
Disactivates mode «SCAN»
SCAN mode
Switch to mode contrast /
Brightness
Control-
continuous zoom
ler
Contrast Switch to mode continuous zoom /
switch to brightness mode
Switch to mode brightness/
Continuous zoom
switch to mode contrast
***
Switches between modes of display brightness, contrast and digital zoom
(modes switch one by one
(brightness -> contrast -> digital zoom -> brightness ...).
Attention! 10 sec after the brightness (or contrast) icon disappears, the
controller is blocked and will not allow setup of brightness, contrast and
continuous zoom.
Resume access to the setup with a short press of the controller.
The display shows the icon of the functions adjusted last.
The sight memorizes the function used last; upon another rotation the
џ
controller sets the function used last.
Parameter values memorized in the sight's memory upon turning off are
џ
used when the riflescope is turned on again.
7

BATTERY INSTALLATION

Turn the battery compartment knob (6) counterclockwise to the "Open"
position and remove it.
Install two CR123A batteries according to the marking on the battery
compartment cover and inside it.
6
OTHER SHORT LONG PRESS
ROTATION
PRESSES
Activates Turn display off
discrete
Power sight off
digital zoom /
PiP (if PiP is
activated)
Turn display on
Activate /
deactivate
mode "Inversion"
activates mode
Distance
«SCAN»
measurement
continuous
distance
measurement
Brightness
setup***
Contrast setup
Enter the menu
Continuous zoom
setup
Replace the battery cover and press it until its clicking position - make sure
the cover is closed on both sides (see Pic.2 in the flyleaf).
Battery charge level is displayed in the status bar (
In case of complete battery discharge, icon
Warning: do not use rechargeable batteries since their use causes inaccurate
battery level indication and possible abrupt disconnection during operation.
Note: please do not use batteries of different types or batteries with
various charge levels.
8

EXTERNAL POWER SUPPLY

The sight can be powered with an external DC power supply (2.1mm pin) with
stabilized voltage ranging from 8V to 15V or a 12V vehicle socket.
џ Connect the plug (13) of the cable to the jack (10) of the sight by matching the
notch in the plug connector and the protrusion of the jack (see Pic.3 in the
flyleaf).
џ Secure the cable by turning clockwise the locking ring of the plug (13).
џ Connect the external power supply (AC/DC) or car adapter to the jack (15) of
the cable.
џ Note: central pin of the power supply that you connect to the "power" jack of
the sight, must have marking "+".
џ The power supply may have marking
џ Connection of an external power supply (icon
automatically cuts off power supply from batteries.
џ External power supply DOES NOT charge the batteries in the sight!
Attention! We suggest that you use battery packs EPS3/EPS3I or EPS5
ensuring from 9 to 20 hours of continuous operation.
9

OPERATION

Installation of mount
Before using the sight you need to install a mount.
The sight can be used with various mount types such as Weaver, Euro-prism,
Los, Side mount, MAK adapter etc. that allow the scope to be installed on
different types of rifles.
The mounting holes in the base of the sight enable the mount to be installed in
one of the multiple positions. The choice of the mounting position helps the
user to ensure the correct eye relief depending on the rifle type.
The mount can be attached with the help of either three or two screws
(supplied) depending on the chosen position of the mount.
Pic. 5
) .
is flashing in the status bar.
.
on the status bar)
Position 1: 3 screws
Position 2: 2 screws
Position 3: 2 screws
7