LENCO SCD-68 DAB+ Benutzerhandbuch Seite 8

Digital audio broadcasting (DAB) radio
1. Set the unit to DAB mode by pressing the Function button (9).
2. Press the Play/pause
time. Press the Skip down
then press the "Stop/Enter" button (10) to confirm the selected channel.
3. Press the Play mode/info button (21) continuously to check the below info released by DAB.
Signal strength  program type  Group name  frequency  signal error  transfer rate  time 
date
4. Adjust volume knob (14) for the desired volume level.
Dynamic range control
This apparatus provides three dynamic range mode to match different program types in the DAB mode.
1. In DAB mode, press the "Menu/Mem/clk-adj" button (12) to enter the "Menu", then press the Skip
down (11) or Skip up
2. Press "Stop/Enter" button (10) to enter the "DRC" setting, then press Skip down
(19) button to select "DRC high/low/off" mode. Then press "Stop/Enter" button (10) to confirm the
setting.
3. In any state press "Menu/Mem/clk-adj" button (12) to quit the setting mode.
Language setting
This apparatus provides 4 language for FM/DAB operation display.
1. In DAB/FM mode, press "Menu/Mem/clk-adj" button (12) to enter the "Menu", then press Skip down
(11) or Skip up
2. Press the "Stop/Enter" button (10) to enter the "System" setting, then press the Skip down
Skip up (19) button to select "Language"; then press the "Stop/Enter" button (10) to enter the
language mode, then press Skip down
between English/French/German/Italian. Then press "Stop/Enter" (10) to confirm the setting.
3. In any state press "Menu/Mem/clk-adj" button (12) to quit the setting mode.
Preset stations
You can store up to total of 20 radio stations in the memory (10-FM/10-DAB).
1. Set to FM/DAB mode.
2. Turn to the desired radio station by "manual" or "auto" tuning method.
3. Press and hold the "Mem/clk-adj" button (12) to enable memory state.
4. Press Skip down
5. Press "Stop/Enter" button (10) to confirm the setting.
6. Repeat step 2 to 5 to store other stations.
Recall preset stations
1. Set to FM/DAB mode
2. Press Pre-up (20) to enable memory recall state.
3. Press Skip down
4. Press "Stop/Enter" (10) again to confirm the recall station.
DAB/FM reset:
In case you would like to erase all the FM/DAB programed memory stations, the operation is as below.
1. Set in DAB or FM mode, press "Menu/Mem/clk-adj" (12) to enter the "Menu", then press Skip down
(11) or Skip up
2. Press "Stop/Enter" (10) to enter the "System" setting, then press Skip down
(19) to select "Factory reset". Then press "Stop/Enter" (10) to confirm the factory reset.
3. The apparatus will erase all the programed memory stations; perform the preset station again as above.
5.3 Playing CD/MP3 disc
 Getting start
1. Press Function (9) to select the CD mode.
2. Open the CD door by pressing the CD door open/close (7). Put a CD disc into the compartment and
close the CD door.
3. Focus search is performance if disc is inside. Total number of tracks is read.
/Scan button (18) once, the unit will start to full scan from range 11b-12d one
(11) or Skip up
(19) button to select "DRC".
(19) button to select "System".
(11) or Skip up (19) to select the desired station memory for storage.
(11) or Skip up (19) to select the desired recall station.
(19) to select "System".
(19) button to select your desired DAB channel and
(11) or Skip up (19) to select your desired language
(11) or Skip up
(11) or Skip up
(11) or
8