Roland V-Drums TD-27KV Aufbauanleitung Seite 2

Connect the pads to the
6
drum sound module
* To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units
before making any connections.
Connection procedure
1. Connect the dedicated connection cable 2. Labels indicating the pad to be connected
to the TRIGGER INPUT connector on the are attached to the cable. Connect the
bottom panel of the drum sound module. cable to the OUTPUT jack of each pad as
shown in the illustration at right.
Insert the connector all the way, then turn the
knobs to fasten it securely. knobs to fasten it securely.
Knob
3. 4.
Using the included trigger cable, connect Using the included connection cables,
crash 2 to the CRASH 2 jack of the TRIGGER connect the snare (PD-140DS) and ride
IN jack on the back panel of the drum (CY-18DR) to the DIGITAL TRIGGER IN ports
sound module. of the drum sound module.
* The CY-13R is used as the crash cymbal. Bell shots are * You may connect to any of the ports 1–3.
not possible.
Cymbal side Drum sound module side
Assembly for a Left-Handed Player
The settings explained in this guide are for a right-handed player. If you want to set up for a left-handed player, assemble the
drum stand according to the procedure described in "Assembling the stand for a left-handed player" in the "MDS-Standard 2
Owner's Manual. " Also, install the pads as shown in the Figure A.
5 Connect the cables to the OUTPUT jack of each pad as shown in the Figure B.
5 Using the included trigger cable, connect crash 2 to the CRASH 2 jack of the drum sound module.
This completes assembly and connections.
9
Set the snare (PD-140DS) and the ride (CY-18DR)
The rst time you connect the PD-140DS and CY-18DR to the DIGITAL TRIGGER IN port, the
following screen will appear. As directed in the screen, assign the PD-140DS as snare, and
assign CY-18DR as ride.
* If you specify the same trigger input as a pad that is connected to a dedicated connection cable or TRIGGER IN
jack, the pad that's connected to that TRIGGER INPUT jack and TRIGGER IN jack won't produce sound.
9
Adjust the hi-hat (VH-10)
If you're using the VH-10 V-hi-hat, execute the o set adjustment from the TD-27 after making connections.
This adjustment is required for pedal movements such as open or close to be detected correctly.
1. With the hi-hat completely separated from the motion sensor unit,
power-on the TD-27.
clutch screw
Separated
motion sensor unit
2. Loosen the clutch screw and let the hi-hat rest naturally on the
motion sensor unit.
3. Press the [SYSTEM] button.
4. Use the cursor buttons to the select "TRIGGER," and press the
[ENTER] button.
5. Use the cursor buttons to the select "HI-HAT," and press the
[ENTER] button.
The TRIGGER HI-HAT screen appears.
USING THE UNIT SAFELY
About WARNING and CAUTION Notices About the Symbols
The symbol alerts the user to important instructions or
Used for instructions intended to alert the
warnings.The specific meaning of the symbol is
user to the risk of death or severe injury
determined by the design contained within the triangle. In
should the unit be used improperly.
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
Used for instructions intended to alert the
The symbol alerts the user to items that must never be
user to the risk of injury or material
carried out (are forbidden). The specific thing that must
damage should the unit be used
not be done is indicated by the design contained within
improperly.
the circle. In the case of the symbol at left, it means that
* Material damage refers to damage or
the unit must never be disassembled.
other adverse effects caused with
The symbol alerts the user to things that must be
respect to the home and all its
carried out. The specific thing that must be done is
furnishings, as well to domestic animals
indicated by the design contained within the circle. In the
or pets.
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
ALWAYS OBSERVE THE FOLLOWING
WARNING
Use only the stand that is recommended Be cautious to protect children from injury
This unit should be used only with a stand Always make sure that an adult is on hand to provide
(MDS-Standard 2) that is recommended by Roland. supervision and guidance when using the unit in places
where children are present, or when a child will be using
Do not place in a location that is unstable
the unit.
When using the unit with a stand (MDS-Standard 2)
Take care not to get burned
recommended by Roland, the stand must be carefully
placed so it is level and sure to remain stable. If not using Otherwise, you risk causing damage or malfunction.
a stand, you still need to make sure that any location you choose
for placing the unit provides a level surface that will properly
support the unit, and keep it from wobbling.
Precautions regarding placement of this unit on a
stand
Use only the speci ed stand(s)
Be sure to follow the instructions in the Owner's Manual
carefully when placing this unit on a stand (Refer to "TD-27KV
This unit is designed to be used in combination with
Setup Guide").
speci c stands (MDS-Standard 2) manufactured by
If it is not set up properly, you risk creating an unstable situation Roland. If used in combination with other stands, you
which could lead to the unit falling or the stand toppling, and risk sustaining injuries as the result of this product dropping
may result in injury. down or toppling over due to a lack of stability.
Plug
& BOW/EDGE
OUTPUT jack
* BELL
OUTPUT
jack is not
used.
Ride
* Insert the plug rmly,
making sure it's all the
way in.
KIK CR1
1.
Use the cursor buttons to select "OK," and press [ENTER] button.
2. Use the cursor buttons to select "PD140DS" or "CY18DR."
3. Use the dial to specify the Assign.
* You can't specify the same assignment multiple times.
6.
Use the dial to set the Trig Type to "VH10."
7.
While reading the meter displayed on the right side of the TD-27's
screen, adjust the o set with the VH-10's o set adjustment screw.
Adjust the o set so that the appear in the meter.
O set adjustment
screw
OPEN CLOSE
8. Fasten the clutch screw at a position where the hi-hat sways
naturally when struck.
9.
Press the [DRUM KIT] button to return to the DRUM KIT screen.
CAUTION
Evaluate safety issues before using stands
Even if you observe the cautions given in the owner's
manual, certain types of handling may allow this product
to fall from the stand, or cause the stand to overturn.
Please be mindful of any safety issues before using this product.
Avoid climbing on top of the unit, or placing heavy
objects on it
Otherwise, you risk injury as the result of the unit
toppling over or dropping down.
Disconnect all cords/cables before moving the unit
Damage or malfunction may result if you fail to
disconnect all cables before moving the unit.
Cautions when moving this unit
If you need to move the instrument, at least two persons
are required to safely lift and move the unit. It should be
WARNING
handled carefully, all the while keeping it level.
Take care so as not to get ngers pinched
When handling the following moving parts, take care
so as not to get ngers, etc., pinched. An adult should
always be in charge of handling these items.
• Stands
• Pedals
Keep small items out of the reach of children
To prevent accidental ingestion of the parts listed below,
always keep them out of the reach of small children.
Included Parts:
CAUTION
• Cable clip • Wing bolts
• Cable tie • Drum key
Removable Parts:
• Screws • Springs
• Hand knobs
• Washers
• Nuts • Protective cap for dedicated
connection cable
• Felt washers
As seen from the back of TD-27KV
CR1
Crash 2
T1
T2
TD-27
T3
Snare
KIK
Labels attached to the end of the cable
Fasten the cables so that they will not obstruct
your playing; use cable clips and cable ties.
Dedicated connection cable
Make sure to wrap the cable ties around the
pipes.
Trigger cable (Crash 2)
Connection cable (Snare, Ride)
Figure A: Setting for a Left-Handed Player
Curve pipe R
Cymbal mount
Pad mount
9
When you've nished making connections, turn on the power as described in "TD-27 Quick Start, " and verify that you
can hear sound.
If you nd the closed hi-hat sound di cult to play, turn the o set
adjustment screw toward "CLOSE. "
If you nd the open hi-hat sound di cult to play, turn it toward
"OPEN. "
* If the sound is interrupted when you play a strong strike, adjust the
o set adjustment screw toward "OPEN. "
Changes
from " " to
"AC"
Additional Precautions
• Use a reasonable amount of care when using the unit's sensors;
and when using its jacks and connectors. Rough handling can
lead to malfunctions.
• This instrument is designed to minimize the extraneous sounds
produced when it's played. However, since sound vibrations
can be transmitted through oors and walls to a greater degree
than expected, take care not to allow these sounds to become
a nuisance others nearby.
• This document explains the speci cations of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
Connect the AC adaptor
7
"HHC" Plug "HH" Plug
& CONTROL & TRIGGER
and speakers
OUT jack OUT jack
* To prevent malfunction and equipment failure, always turn down the volume,
and turn o all the units before making any connections.
HH Connect the AC adaptor, headphones, or speakers.
* Use the cord hook located on the bottom of the unit to secure the AC
HHC
adaptor cord as shown in the illustration.
The cables labeled SNR,
RD, and RDB are not used.
Leave the caps attached,
and secure them so that
they will not interfere with
your performance.
SNR
RD
RDB
The cord of
the supplied
AC Adaptor
AC outlet
Figure B: As seen from the back of TD-27KV
CR1
HH
HHC
TD-27
Snare
SNR
RD
RDB
Setting example
Pad Assign
PD-140DS SNARE
CY-18DR RIDE
4. Press the [DRUM KIT] button to return to the DRUM KIT screen.
This completes settings.
Fixing the hi-hat cables
Wind the
cable tie once
Tighten it not to slip
Turn back to x the cables
NOTE
5 Continuous playing may cause dis-coloration of the pad, but this will not
a ect the Pad's function.
5 If the hi-hat clutch has been detached from the hi-hat, refer to "If the Clutch
Was Apart from the Hi-Hat" in the "VH-10 Owner's Manual. "
IMPORTANT NOTES
Intellectual Property Right
• It is forbidden by law to make an audio recording, video
recording, copy or revision of a third party's copyrighted work
(musical work, video work, broadcast, live performance, or
other work), whether in whole or in part, and distribute, sell,
lease, perform, or broadcast it without the permission of the
copyright owner.
• Do not use this product for purposes that could infringe on a
copyright held by a third party. We assume no responsibility
whatsoever with regard to any infringements of third-party
copyrights arising through your use of this product.
• The copyright of content in this product (the sound waveform
data, style data, accompaniment patterns, phrase data, audio
loops and image data) is reserved by Roland Corporation.
• Purchasers of this product are permitted to utilize said content
(except song data such as Demo Songs) for the creating,
performing, recording and distributing original musical works.
• Purchasers of this product are NOT permitted to extract
said content in original or modi ed form, for the purpose of
distributing recorded medium of said content or making them
available on a computer network.
• The SD logo and SDHC logo are trademarks of SD-
3C, LLC.
• ASIO is a trademark and software of Steinberg Media
Technologies GmbH.
• This product contains eParts integrated software platform of
eSOL Co.,Ltd. eParts is a trademark of eSOL Co., Ltd. in Japan.
Cord
Hook
Crash 2
T1 T2 Ride
T3
KIK
Leave some slack in the cables
• The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
Roland is under license.
• This Product uses the Source Code of T-Kernel under T-License
2.0 granted by the T-Engine Forum (www.tron.org).
• Roland, BOSS, and V-Drums are either registered trademarks or
trademarks of Roland Corporation in the United States and/or
other countries.
• Company names and product names appearing in this
document are registered trademarks or trademarks of their
respective owners.