Makita DUH501 Betriebsanleitung Seite 12

NOTICE:
Depending on the usage conditions,
the tool is automatically turned off w ithout any
indication if the tool is overloaded by entangled
branches or debris. In this case, s w itch off the
tool and remove the battery cartridge, and then
remove entangled branches or debris using tools
such as pliers. After removing the branches or
debris, install the battery cartridge and turn on
the tool again.
Overheat protection for tool or battery
There are two types of overheating; tool overheating
and battery overheating. When the tool over heating
occurs, all speed indicators blink. When the battery over
indicator blinks.
h eating o c c urs,
If the overheating occurs, the tool stops automatically.
Let the tool and/or battery cool down before turning the
tool on again.
Overdischarge protection
When the battery capacity becomes low, the tool stops
automatically and indicator blinks.
I f t h e tool d oes not operate e v en w h en t h e s w it c h es are
operated, remove the battery from the tool and charge
the battery.
Angle setting of the handle
CAUTION:
Al w ays make sure that the handle
is locked in the desired position before operation.
CAUTION:
Do not pull do w n the lever to
unlock the handle w hile pulling the s w itch trigger.
Do not pull the s w itch trigger w hile pulling do w n
the lever and turning the handle. F ailure to d o so
may cause a malfunction of the tool.
Y ou c an set t h e angle o f t h e h an d le to 0 ° , 4 5 ° , or 9 0 °
to t h e le f t or rig h t. T o c h ange t h e angle o f t h e h an d le,
turn t h e h an d le w h ile pulling d o w n t h e le v er, an d t h en
release t h e le v er.
Fig.3: 1. L e v er
Pow er sw itch action
WARNING:
For your safety, this tool is
equipped w ith lock-off lever w hich prevents the
tool from unintended starting. NEVER use the tool
if it runs w hen you simply press the s w itch lever
and pull the s w itch trigger w ithout pressing the
lock-off lever. Return the tool to our authorized
service center for proper repairs BEFORE further
usage.
WARNING:
NEVER tape do w n or defeat pur-
pose and function of lock-off lever.
WARNING:
Before installing the battery car-
tridge on the tool, al w ays check to see that the
s w itch trigger and s w itch lever actuate properly
and return to the " OFF " position w hen released.
O perating a tool w it h a s w it c h t h at d oes not a c tuate
properly can lead to loss of control and serious per-
sonal injury.
Never put your finger on the
CAUTION:
s w itch w hen carrying. The tool may start uninten-
tionally and cause injury.
NOTICE:
Do not pull the s w itch trigger hard w ith-
out pressing the lock-off lever. This can cause
s w itch breakage.
Press and hold the main power button to turn on the
tool. T h e po w er lamp lig h ts up w h en t h e tool is turne d
on. T o turn o f f t h e tool, press an d h ol d t h e main po w er
button again. The power lamp goes off when the tool is
turne d o f f .
Fig.4: 1. Power lamp 2. Main power button
NOTE: The tool is automatically turned off if the tool is
not operate d f or a c ertain perio d .
To prevent the switch trigger from being accidentally
pulle d , a lo c k-o f f le v er is pro v i d e d . T o start t h e tool,
d epress t h e lo c k-o f f le v er, an d t h en press t h e s w it c h
le v er an d pull t h e s w it c h trigger. T h e tool spee d
increases by increasing pressure on the switch trigger.
R elease t h e s w it c h trigger to stop.
Fig.5: 1. S w it c h le v er 2. L o c k-o f f le v er 3. S w it c h
trigger
Speed adjusting
You can adjust the tool speed by tapping the main
power button.
Each time you tap the main power button, the level of
spee d w ill c h ange.
Fig.6: 1. Power lamp 2. Main power button
Indicator
Reverse button for debris removal
WARNING:
debris cannot be removed by the reverse func-
tion, s w itch off the tool and remove the bat-
tery cartridge, and then remove the entangled
branches or debris using tools such as pliers.
Failure to switch off the tool and remove the bat-
tery cartridge may result in serious personal injury
f rom a c c i d ental start-up. R emo v ing t h e entangle d
branches or debris by hand may cause an injury,
since the shear blades may move in reaction to
remo v ing t h em.
12 ENGLISH
Mode Stroke speed
H igh 4 ,4 00 min
Med ium 3,6 00 min
L ow 2,000 min
If the entangled branches or
-1
-1
-1